Graco TI3840a Direct Impingement Round Pattern Guns, Flow Rate in gpm lpm

Page 6

List of Models/Selection Guide

Direct Impingement Round Pattern Guns

Use only these mix module/tip combinations.

Gun Part No., Series	Slip-Fit™Polycarballoy™ Mix Module Part No.,	Round CeramTip™ Part No.,
	see page 48 for numbering code	see page 50 for numbering code


247003, A	XR2323	RTM040

247006, A	XR2929	RTM030

247007, A	XR2929	RTM040

247011, A	XR3535	RTM030

247012, A	XR3535	RTM040

247013, A	XR3535	RTM055

247018, A	XR4747	RTM040

247019, A	XR4747	RTM055

247025, A	XR5757	RTM055

247026, A	XR5757	RTM070

FLOW RATE in gpm (lpm)*

* To calculate flow in lb/min, multiply gpm rate by 10. Example: 2 gpm x 10 = 20 lb/min.

5.0
(18.9)
(15.1)									XR5757//RTM070
4.0
3.0
(11.4)									XR4747/RTM055
									XR4747/RTM055
2.0										XR3535/RTM040
2.0
(7.6)									XR2929/RTM040
									XR2929/RTM040
											040
1.0										TM
1.0									XR2323/R
(3.8)
0
800		1250		1700		2150		2600		3050		3500
(5.6, 56)		(8.7, 87)		(11.9, 119)		(15.0, 150)		(18.2, 182)		(21.3, 213)		(24.5, 245)

PRESSURE in psi (MPa, bar)

6

309856U

Image 6

Contents Important Safety Instructions Plural Component, Impingement Mix Mechanical Purge Spray GunContents Manual Conventions List of Models/Selection Guide Standard Round Pattern GunsPressure in psi MPa, bar Standard Flat Pattern Guns 247291, aDirect Impingement Round Pattern Guns Flow Rate in gpm lpmDirect Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Overall View KeyKeep a and B Components Separate Piston Safety LockIsocyanate Hazard GroundingSetup ISODisengage piston safety lock, Adjust Purge Rod 1/4 TurnAdjust Flat CeramTip Daily Shutdown Follow Pressure Relief Procedure,Shutdown Shutdown for More than a DayPressure Relief Procedure Optional Configurations Optional Fluid Manifold PositionFluid Hoses Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Air HoseMaintenance Clean Muffler Clean Outside of GunClean Air Cap Clean Fluid ManifoldClean Slip-Fit Polycarballoy Mix Module Cleaning Component a ISO PortsImpingement Port Cleanout Drill Sizes XF1313 #81 Cleanout Drill Sizes for Round CeramTips Clean CeramTipExternal Quick Cleaning Method Round CeramTipClean Purge Rod Adjust Purge Rod,Stuck Purge Rod Adjust Front Rod Seal Reassemble Front End, Adjust Purge Rod,Disassemble Front End, Adjust Rear Rod Seal Troubleshooting See Clean Purge Rod,Adjust Rear Rod Seal, Theory of Operation Gun Triggered Fluid SprayingGun Detriggered Mechanical Purging Cutaway View Lubrication RepairTools Required Replace CeramTipDisassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Piston Safety Lock Air Valve309856U Parts Flush Manifold DetailPart No. Description Qty HandleStandard Round Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Flat Pattern GunsDirect Impingement Round Pattern Guns Direct Impingement Flat Pattern GunsFlat CeramTip Part Numbering Code CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTipsDrill Bit Kits Kit Part No Qty in Kit Drill Bit Size Illustration NominalGun Repair Kits Check Valve Filter Screen Kits 10 per kitAccessories Solvent Flush Pail Kit Hose Adapter KitsPour Nozzle Kit Technical Data Category DataGraco Standard Warranty Graco InformationToll Free