Graco TI3840a important safety instructions Direct Impingement Flat Pattern Guns

Page 7

List of Models/Selection Guide

Direct Impingement Flat Pattern Guns

Use only these mix module/tip combinations.

Gun Part No., Series	Slip-Fit™Polycarballoy™ Mix Module Part No.,	Flat CeramTip™ Part No.,
	see page 48 for numbering code	see page 50 for numbering code


247050, A	XF1313	FTM317

247051, A	XF1313	FTM424

247057, A	XF1818	FTM317

247058, A	XF1818	FTM424

247061, A	XF2323	FTM424

247062, A	XF2323	FTM438

247063, A	XF2323	FTM624

247065, A	XF2929	FTM424

247066, A	XF2929	FTM438

247067, A	XF2929	FTM624

247073, A	XF3535	FTM438

247074, A	XF3535	FTM624

247075, A	XF3535	FTM638

247081, A	XF4747	FTM624

247082, A	XF4747	FTM638

247083, A	XF4747	FTM838

247089, A	XF5757	FTM638

247090, A	XF5757	FTM838

247091, A	XF5757	FTM848

247163, A	XF2332	FTM438

309856U

7

Image 7

Contents Plural Component, Impingement Mix Mechanical Purge Spray Gun Important Safety InstructionsContents Manual Conventions Standard Round Pattern Guns List of Models/Selection GuidePressure in psi MPa, bar 247291, a Standard Flat Pattern GunsFlow Rate in gpm lpm Direct Impingement Round Pattern GunsDirect Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Key Overall ViewGrounding Piston Safety LockIsocyanate Hazard Keep a and B Components SeparateISO SetupDisengage piston safety lock, 1/4 Turn Adjust Purge RodAdjust Flat CeramTip Shutdown for More than a Day Follow Pressure Relief Procedure,Shutdown Daily ShutdownPressure Relief Procedure Optional Fluid Manifold Position Optional ConfigurationsAir Hose Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Fluid HosesMaintenance Clean Fluid Manifold Clean Outside of GunClean Air Cap Clean MufflerCleaning Component a ISO Ports Clean Slip-Fit Polycarballoy Mix ModuleImpingement Port Cleanout Drill Sizes XF1313 #81 Round CeramTip Clean CeramTipExternal Quick Cleaning Method Cleanout Drill Sizes for Round CeramTipsAdjust Purge Rod, Clean Purge RodStuck Purge Rod Reassemble Front End, Adjust Purge Rod, Adjust Front Rod SealDisassemble Front End, Adjust Rear Rod Seal See Clean Purge Rod, TroubleshootingAdjust Rear Rod Seal, Gun Triggered Fluid Spraying Theory of OperationGun Detriggered Mechanical Purging Cutaway View Replace CeramTip RepairTools Required LubricationDisassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Air Valve Piston Safety Lock309856U Flush Manifold Detail PartsHandle Part No. Description QtyStandard Flat Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Round Pattern GunsDirect Impingement Flat Pattern Guns Direct Impingement Round Pattern GunsFlat CeramTips CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTip Part Numbering CodeKit Part No Qty in Kit Drill Bit Size Illustration Nominal Drill Bit KitsCheck Valve Filter Screen Kits 10 per kit Gun Repair KitsAccessories Hose Adapter Kits Solvent Flush Pail KitPour Nozzle Kit Category Data Technical DataGraco Information Graco Standard WarrantyToll Free