Graco 288046, Series B important safety instructions Connect Air Line

Page 9

Installation

Connect Air Line

1.Install an air/water separator and an air line filter to ensure a clean, dry air supply to the gun. Dirt and moisture in the line can ruin the appearance of your finished piece.

2.Install an air pressure regulator on each gun air sup- ply line.

3.For manifolds with separate fan and atomization ports, the gun cylinder, fan, and atomization air must be supplied and regulated separately. For manual valve manifolds, only one supply line is required for both atomization and fan air.

A minimum of 50 psi (0.34 MPa, 3.4 bar) air pres- sure must be supplied to the cylinder for proper operation. Set the atomization air as needed for complete atomization of the entire pattern. The tip size is the primary controller of the pattern size. Use the fan air only as needed to slightly adjust the pattern size.

4.Install a bleed-type master air shutoff valve on the main air line. Install an additional bleed-type valve on each pump air supply line, downstream of the pump air regulator, to relieve air trapped between this valve and the pump after the air regulator is shut off.

The bleed-type air shutoff valve is required in your sys- tem to relieve air trapped between this valve and the pump after the air regulator is closed. Trapped air can cause the pump to cycle unexpectedly, which could result in serious injury.

5.Install a bleed-type air shutoff valve on each gun air supply line, downstream of the gun air regulator, to shut off air to the gun.

6.For manifolds with separate fan and atomization ports, connect a separate air supply line to the gun atomizing air inlet (D) and cylinder air inlet (C). Con- nect an air supply line to the fan air inlet (E) if desired. See FIG. 6. For manifolds with a manual fan valve, only one supply line is required for both atom- ization and fan air.

The gun atomizing and fan air inlets are 3/8 in. (9.5 mm) O.D. tubing compatible. The cylinder air inlet accepts 1/4 in. (6.3 mm) O.D. tubing.

311052H

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Automatic G40 Air-Assisted Spray Guns Contents G40 Standard Spray Gun, 288046, Series B ModelsG40 Standard Spray Gun, 24F835, Series B G40 Plastic Seat Spray Gun, 288044, Series BEquipment Misuse Hazard Pressurized Equipment Hazard Ventilate Spray Booth InstallationConfigure Gun and Manifold Circulating SystemGround System Install Air FittingsReciprocating Arm Rod Mount Mount GunStationary Support Retrofit Adapter PlateConnect Air Line Side Mounted Manifold Ports Connect Fluid LineSetup Pressure Relief Procedure Adjust Spray PatternOperation Incorrect Apply FluidCorrect No air Too little air Correct amount AirDaily Gun Care MaintenanceFlushing and Cleaning General System MaintenanceTurn off the solvent supply Troubleshooting General TroubleshootingProblem Cause Solution Problem Cause Solution Spray Pattern Troubleshooting Service DisassemblyItems Needed for Service TI8173b Cutaway View Part No Gun Shown Reassembly Diffuser Seat ReplacementParts AA RAC Assembly included with Model 288053 onlyPart Ref. No. No Description Qty PartsNorth America and International Manifold Description QtyManifold with Bottom Fluid Ports Part No. Description QtyPart No C343 Side Fluid Ports and Fan Adjustment ValveRING, Ptfe 311052H AAP Series Tip and Air Cap Selection Charts AAP Series Precision Spray TipsTypical Air Application Tip Used With Consumption LTX Series RAC Tip Selection Charts For use with G40 RAC HousingLTX Reverse-A-Clean RAC Spray Tips RAC Switch Tips FFT Fine Finish RAC Spray TipsWRX Wide RAC Spray Tips Accessories Grounding Clamp and Wire In-line Fluid Filter Ultimate Gun Cleaning Kit 15C161Air Cap Seal Kit Plastic Seat Repair KitDimensions Mounting Hole Layout Gun with Rear Port Manifold Rear Port ManifoldTriggering Speed Technical DataSound Data dBa Models 3/16 in. ball Cylinder Air Pressure Fluid PressureGraco Information Graco Standard Warranty
Related manuals
Manual 12 pages 23.99 Kb Manual 20 pages 21.73 Kb Manual 14 pages 60.52 Kb Manual 16 pages 50.96 Kb

288046, Series B specifications

Graco Series B, 288046 is a top-tier product designed to meet the rigorous demands of various applications in industries such as manufacturing, automotive, and construction. Renowned for its reliability and efficiency, this product stands out due to its innovative features and robust technology.

One of the standout features of the Graco Series B, 288046 is its advanced air-powered design. This design allows for smooth and consistent fluid transfer, minimizing downtime and enhancing productivity. The air-driven operation not only offers greater control over the flow rates but also ensures that the system can operate in situations where electric power may be unavailable or impractical. This versatility makes it ideal for various work environments.

The Series B is equipped with a high-performance motor that delivers exceptional power output while maintaining energy efficiency. This feature is particularly advantageous for businesses looking to reduce operational costs without compromising on performance. The motor is engineered to handle different fluid viscosities, making the Series B versatile for use with a wide range of materials, including paints, adhesives, and sealants.

Durability and ease of maintenance are key characteristics of the Graco Series B, 288046. Constructed from high-quality materials, the product is built to withstand harsh conditions, ensuring a long-lasting lifespan. Additionally, its modular design simplifies maintenance and repairs, allowing for quick replacements of components and minimal disruption to operations.

Safety is another paramount consideration incorporated into the Series B design. It features comprehensive safety mechanisms that protect users and equipment alike, reducing the risk of accidents during operation. This is especially crucial in environments where workers are regularly handling hazardous materials.

Graco also emphasizes user-friendly functionality. The Series B showcases intuitive controls, enabling operators to quickly familiarize themselves with the system and operate it efficiently. The product also includes adjustable pressure settings, allowing for precise application suited to specific tasks.

In conclusion, the Graco Series B, 288046 is an exemplary solution for companies seeking a reliable, efficient, and safe fluid handling system. With its advanced technologies, user-friendly features, and robust construction, it offers unmatched performance across various industries, ensuring optimal productivity and safety.
Top Page Image Contents