Graco Series B, 288046 Installation, Ventilate Spray Booth, Configure Gun and Manifold

Page 6

Installation

Installation

Ventilate Spray Booth

Check and follow all National, State, and Local codes regarding air exhaust velocity requirements.

Check and follow all local safety and fire codes.

Configure Gun and Manifold

The gun is supplied with an internal fluid plug and seals (5, 6, 7). To use the gun in a circulating system, remove the internal plug. In a non-circulating system, leave the plug in place to minimize flush time.

Circulating System

1.Apply anti-seize lubricant 222955 to the threads and mating faces of the manifold (101) and the elbows (107), supplied unassembled.

2.Install the elbows (107) in both fluid ports of the manifold (101).

3.Connect the fluid supply line to one elbow and the fluid return line to the other. The manifold fluid ports are reversible.

4.Install the gun on the manifold, using the four screws (17). Start the threads of all four screws, and tighten the front two screws first, and then tighten the back two screws to 65 in-lb (7.3 N•m).

Non-circulating System

1.See FIG. 1. Apply anti-seize lubricant 222955 to the threads and mating faces of the manifold (101), plug (109), and elbow (107), supplied unassembled.

2.Install an elbow (107) in one fluid port of the mani- fold (101), and a plug (109) in the other port.

3.Install the internal plug (5) in the gun fluid port on the same side as the manifold plug.

4.Connect the fluid supply line to the manifold elbow (107).

5.Install the gun on the manifold, using the four screws (17). Start the threads of all four screws, and tighten the front two screws first, and then tighten the back two screws to 65 in-lb (7.3 N•m).

1

Remove when used in circulating systems.

2

Replace with a reducing nipple (107) when used in

 

circulating systems.

3

Install optional filter in fluid inlet port. See Accessories,

 

page 34.

7

3

 

6

 

 

 

101

1

5

107

 

 

2109

TI8587b

FIG. 1: Non-Circulating Setup Shown (cutaway view)

6

311052H

Image 6
Contents Automatic G40 Air-Assisted Spray Guns Contents G40 Standard Spray Gun, 24F835, Series B ModelsG40 Standard Spray Gun, 288046, Series B G40 Plastic Seat Spray Gun, 288044, Series BEquipment Misuse Hazard Pressurized Equipment Hazard Configure Gun and Manifold InstallationVentilate Spray Booth Circulating SystemInstall Air Fittings Ground SystemStationary Support Mount GunReciprocating Arm Rod Mount Retrofit Adapter PlateConnect Air Line Connect Fluid Line Side Mounted Manifold PortsSetup Pressure Relief Procedure Adjust Spray PatternOperation Correct Apply FluidIncorrect No air Too little air Correct amount AirMaintenance Daily Gun CareGeneral System Maintenance Flushing and CleaningTurn off the solvent supply Troubleshooting General TroubleshootingProblem Cause Solution Problem Cause Solution Spray Pattern Troubleshooting Service DisassemblyItems Needed for Service TI8173b Cutaway View Part No Gun Shown Diffuser Seat Replacement ReassemblyAA RAC Assembly included with Model 288053 only PartsParts Part Ref. No. No Description QtyDescription Qty North America and International ManifoldPart No. Description Qty Manifold with Bottom Fluid PortsSide Fluid Ports and Fan Adjustment Valve Part No C343RING, Ptfe 311052H AAP Series Tip and Air Cap Selection Charts AAP Series Precision Spray TipsTypical Air Application Tip Used With Consumption LTX Series RAC Tip Selection Charts For use with G40 RAC HousingLTX Reverse-A-Clean RAC Spray Tips RAC Switch Tips FFT Fine Finish RAC Spray TipsWRX Wide RAC Spray Tips Accessories Air Cap Seal Kit Ultimate Gun Cleaning Kit 15C161Grounding Clamp and Wire In-line Fluid Filter Plastic Seat Repair KitDimensions Mounting Hole Layout Rear Port Manifold Gun with Rear Port ManifoldSound Data dBa Technical DataTriggering Speed Models 3/16 in. ball Cylinder Air Pressure Fluid PressureGraco Standard Warranty Graco Information
Related manuals
Manual 12 pages 23.99 Kb Manual 20 pages 21.73 Kb Manual 14 pages 60.52 Kb Manual 16 pages 50.96 Kb

288046, Series B specifications

Graco Series B, 288046 is a top-tier product designed to meet the rigorous demands of various applications in industries such as manufacturing, automotive, and construction. Renowned for its reliability and efficiency, this product stands out due to its innovative features and robust technology.

One of the standout features of the Graco Series B, 288046 is its advanced air-powered design. This design allows for smooth and consistent fluid transfer, minimizing downtime and enhancing productivity. The air-driven operation not only offers greater control over the flow rates but also ensures that the system can operate in situations where electric power may be unavailable or impractical. This versatility makes it ideal for various work environments.

The Series B is equipped with a high-performance motor that delivers exceptional power output while maintaining energy efficiency. This feature is particularly advantageous for businesses looking to reduce operational costs without compromising on performance. The motor is engineered to handle different fluid viscosities, making the Series B versatile for use with a wide range of materials, including paints, adhesives, and sealants.

Durability and ease of maintenance are key characteristics of the Graco Series B, 288046. Constructed from high-quality materials, the product is built to withstand harsh conditions, ensuring a long-lasting lifespan. Additionally, its modular design simplifies maintenance and repairs, allowing for quick replacements of components and minimal disruption to operations.

Safety is another paramount consideration incorporated into the Series B design. It features comprehensive safety mechanisms that protect users and equipment alike, reducing the risk of accidents during operation. This is especially crucial in environments where workers are regularly handling hazardous materials.

Graco also emphasizes user-friendly functionality. The Series B showcases intuitive controls, enabling operators to quickly familiarize themselves with the system and operate it efficiently. The product also includes adjustable pressure settings, allowing for precise application suited to specific tasks.

In conclusion, the Graco Series B, 288046 is an exemplary solution for companies seeking a reliable, efficient, and safe fluid handling system. With its advanced technologies, user-friendly features, and robust construction, it offers unmatched performance across various industries, ensuring optimal productivity and safety.