|
| Troubleshooting |
|
|
|
Problem | Cause | Solution |
|
|
|
|
|
|
Pump output is low | Strainer (16) is clogged | Clean strainer. |
|
|
|
| Piston ball (206) is not seating | Service piston ball. Manual 309250. |
|
|
|
| Piston packings are worn or damaged | Replace packings. Manual 309250. |
|
|
|
| Replace | |
|
|
|
| Intake valve ball is not seating properly | Clean intake valve. Manual 309250. |
|
|
|
| Intake valve ball is packed with material | Clean intake valve. Manual 309250. |
|
|
|
| Engine speed is too low | Increase throttle setting. Manual 310802. |
|
|
|
| Clutch is worn or damaged | Adjust or replace clutch. Page 9. |
|
|
|
| Pressure setting is too low | Increase pressure. Manual 310802. |
|
|
|
| Fluid filter (29), tip filter or tip is | Clean filter. Manual 310802 or 309639. |
| clogged or dirty |
|
|
|
|
| Large pressure drop in hose with | Use larger diameter hose and/or |
| heavy materials | reduce overall length of hose. Use of |
|
| more than 100 ft of 1/4 in. hose signifi- |
|
| cantly reduces performance of sprayer. |
|
| Use 3/8 in. hose for optimum perfor- |
|
| mance (50 ft minimum). |
|
|
|
Excessive paint leakage into throat | Throat packing nut is loose | Remove throat packing nut spacer. |
packing nut |
| Tighten throat packing nut just enough |
|
| to stop leakage. |
|
|
|
| Throat packings are worn or damaged | Replace packings. Manual 309250. |
|
|
|
| Displacement rod is worn or damaged | Replace rod. Manual 309250. |
|
|
|
Fluid is spitting from gun | Air in pump or hose | Check and tighten all fluid connections. |
|
| Prime pump. Manual 310802. |
|
|
|
| Tip is partially clogged | Clear tip. Manual 309639. |
|
|
|
| Fluid supply is low or empty | Refill fluid supply. Prime pump. Manual |
|
| 310802. Check fluid supply often to |
|
| prevent running pump dry. |
|
|
|
Pump is difficult to prime | Air in pump or hose | Check and tighten all fluid connections. |
|
| Reduce engine speed and cycle pump |
|
| as slowly as possible during priming. |
|
|
|
| Intake valve is leaking | Clean intake valve. Be sure ball seat is |
|
| not nicked or worn and that ball seats |
|
| well. Reassemble valve. |
|
|
|
| Pump packings are worn | Replace pump packings. Manual 309250. |
|
|
|
| Paint is too thick | Thin the paint according to the sup- |
|
| plier's recommendations |
|
|
|
| Engine speed is too high | Decrease throttle setting before prim- |
|
| ing pump. Manual 310802. |
|
|
|
Clutch squeaks each time clutch | Clutch surfaces are not matched to each | Clutch surfaces need to wear into each |
engages | other when new and may cause noise | other. Noise will dissipate after a day of |
|
| run time. |
|
|
|
High engine speed at no load | Misadjusted throttle setting | Reset throttle to 3300 engine rpm at no |
|
| load |
|
|
|
| Worn engine governor | Replace or service engine governor |
|
|
|
310813 Rev C | 7 |