Setup, Operation, Pressure Relief Procedure

T1-TITANIUM NON-HVLP SPRAY GUN

Setup

•Check that your shop air provides adequate air flow.

•Use a minimum 5/16 in. ID air supply hose.

•Set air and fluid pressure regulator according to paint man- ufacturer’s recommendation for conventional equipment. Do not exceed 100 psi (0.7 MPa, 7 bar).

•Make sure no air restrictions, such as low-volume cheater- valves, obstruct the air flow. If an air adjusting valve is desired, use a SHARPE Air Adjusting Valve 24AAV (part no. 2210), 36AAV-HOV (part no. 3310) or HOV (part no. U04410).

•Install a shutoff valve (not supplied) downstream of the air regulator to shut off gun air.

•Install a shutoff valve (not supplied) on the fluid supply line to shut off fluid to the gun.

•Install an inline air filter (not supplied) to clean and dry the air supply to the gun.

1.Connect a clean, dry, filtered air supply to gun air inlet (9).

2.Connect fluid supply line to the gun fluid inlet (38).

If this is first time using the equipment, flush the spray gun.

17d

FIG. 1

Operation

Pressure Relief Procedure

WARNING

Follow Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment. Read warnings, page 2.

1.Turn off gun air and fluid supply.

2.Trigger the gun to relieve pressure.

Flushing

WARNING

Read warnings, page 2.

Flush before using the equipment, before changing colors, and when you are done spraying. Use solvent that is compatible with gun wetted parts and fluid that will be sprayed. Flush at lowest possible pressure.

Refer to Compliant Cleaning Methods, page 4, to com- ply with air quality laws if applicable.

1.Follow Pressure Relief Procedure.

2.Connect a solvent supply line to the gun fluid inlet (38).

3.Spray into grounded metal waste container until equipment is clean.

4.Follow Pressure Relief Procedure.

Spraying

CAUTION

Excessive atomizing air pressure can increase over-spray, reduce transfer efficiency, result in a poor quality finish from dry spray.

1.Connect the fluid supply line to the gun fluid inlet (38).

2.Turn on shop air to gun and set atomizing pressure with the gun fully triggered.

3.Adjust the pattern size and shape with the spray width adjustment knob (17d). Turn knob clockwise to reduce pat- tern size and counterclockwise to increase it.

See Troubleshooting guide if you experience an irregular pattern.

4.Fluid control knob (16) is factory set for maximum needle trigger travel and material flow. To decrease needle/trigger travel and decrease fluid flow, turn the knob clockwise.

5.Adjust fluid pressure regulator until desired fluid flow rate is reached.

310584D

5435, 5430, 310584D, T1-Titanium specifications

Graco Inc is a leading manufacturer in the field of fluid handling systems, known for its innovative and reliable products. One of its standout offerings is the T1-Titanium paint sprayers, specifically the models 310584D, 5430, and 5435. These sprayers cater to professionals and DIY enthusiasts alike, providing exceptional performance for various painting applications, including residential, commercial, and industrial projects.

The T1-Titanium series is characterized by its lightweight and durable design, highlighting the use of titanium in its construction. This material not only ensures longevity but also makes the sprayers easier to handle, reducing fatigue during extended use. The models are engineered for high efficiency, allowing users to complete projects faster while maintaining a quality finish.

One of the main features of the T1-Titanium sprayers is their adjustable pressure control. This technology gives users the flexibility to adjust the spray pattern and flow rate according to the specific requirements of their projects. Whether applying broad strokes on large surfaces or dealing with intricate detailing, the models effectively accommodate various needs, ensuring optimal coverage and reduced overspray.

The 310584D, 5430, and 5435 also integrate Graco's ProConnect system, which allows for quick and easy replacement of the pump without the need for additional tools. This feature significantly reduces downtime, enabling painters to keep projects on schedule. Additionally, the models are equipped with a robust filtration system that ensures the sprayers operate cleanly, minimizing clogs and extending the overall life of the equipment.

Another important characteristic of these sprayers is their versatility; they are compatible with a wide range of coatings, including stains, sealers, and latex paints. This adaptability makes them ideal for various applications, from residential repaints to large-scale commercial projects.

In summary, Graco Inc's T1-Titanium paint sprayers, particularly the 310584D, 5430, and 5435 models, are exemplary products in the painting equipment market. With their lightweight titanium construction, adjustable pressure control, ProConnect system, and versatility with coatings, these sprayers are designed to meet the demands of both professionals and DIYers, delivering exceptional results with ease and efficiency.