Graco Inc GC-1412 important safety instructions System Start-Up Instructions

Page 20

Start-Up

The following assumes that all connections are tight.

System Start-Up Instructions

1.Select a clean dry air supply.

2.Attach a 3/8” or larger air hose to the Air Manifold Inlet. 'RQRWXVHTXLFNGLVFRQQHFW¿WWLQJV

3.Attach grounding clamp assembly, P/N 17440-00, to the slave pump.

Before turning on main air, check all On/Off Ball Valves, making certain all Valves are in the “Off” position and set all regulators in their “Off” position. (Turn knob counter- clockwise for OFF or reduced pressure setting.)

5.Place the mixing element straight into the front gun housing. (refer to spray gun user manual)

6.Place the retaining nut along with the spray tip and spray tip spacer onto the gun housing. (refer to spray gun user manual)

7.Push the slide valve to the open position.

	Attach Here	8. 2SHQWKHDLUYDOYHSQRQWKHVROYHQWWDQNDQG
	Attach Here	adjust the solvent pressure to 90 PSI (6.2 bar). Open
		adjust the solvent pressure to 90 PSI (6.2 bar). Open

WKHEDOOYDOYHSQRQWKHVROYHQWWDQN1H[W

open ball valve p/n 23518-00 on the gun to verify that

VROYHQWZLOOÀRZRXWRIWKHIURQWRIWKHJXQWKURXJKWKH

dispense tip, then close the valve.

Do not exceed 20 PSI (1.4 bar)on the material

UHJXODWRUXQWLODVWHDG\PDWHULDOÀRZKDVEHHQ

established.

4.Securely attach Clamp, P/N 7749-00, to permanently grounded rod or pipe.

13193-00

Regulator

Valve	Ball valve
18470-00	Ball valve
	3165

Attach

Here

7749-00

7750-049654-00

TO SLAVE PUMP

20

GC-1412D

Image 20

Contents Internal Chop System GC-1412D Contents SUHYHQW¿UHDQGHSORVLRQ ‡.HHSDZRUNLQJ¿UHHWLQJXLVKHULQWKHZRUNDUHDComply with all applicable safety regulations Skin Injection HazardImportant Safety Information Methyl Ethyl Ketone Peroxide MekpPolyester Resins and Gel-Coats Spraying and Lamination OperationsWKHZRUNDUHD GroundingFor detailed grounding instructions of all equipment Set-Up Tools Required6WDQGDUGZUHQFK VRFNHWVHW Loosen clamp bolts to expose pump mountingVLRQQXWWRORFNGRZQWKHWXELQJ Pump Install tubing p/n 9704-11 from the catalyst jug toProper sized wrenches, carefully tighten the compres Set-Up Indy Chopper Gun Option Lay all of the hoses out straight11. a. Attach the hoses to the gun Them with tape about every 2 feetYellow Solvent Hose p/n ODFN0DWHULDOKLS+RVHFrom Spool To Gun WKHERRPZLWKELQGLQJVWUDSVTo Boom Formula Chopper Gun Option 16. a. Attach the hoses to the gun 6HFXUHWKH¿YHKRVHVWRWKH Attach the hoses to the unit as shown Part Description Qty 1XPEHUPressure Relief Procedure 7RUHOLHYHÀXLGDQGDLUSUHVVXUHVStart-Up System Start-Up InstructionsVWURNHWKHSXPSXQWLOLWGHYHO NQREWRGLVHQJDJHWKHFDWDO\VWDO\VWÀRZVEDFNWRWKHERWWOH Shut-down Shut-Down InstructionsFormula Gun WULJJHUORFNSQParts 0DWHULDO6SUD\1ROHVStandard Equipment Part Description6XE$VVHPEO\UDZLQJV GAM-268-01 Material Pick-Up Kit Part Description Qty Filter Options Part DescriptionOptional Part Description Qty Air Manifold Part Description Qty6ROYHQW7DQN Part Description Qty LW$VVHPEO\ +HDWHU&RQYHUVLRQ.LW$VVHPEO\ Maintenance Clean pump lube cup and add fresh pump lubeBottle Fluid Filter Assembly QVSHFWDQGFOHDQ¿OWHURQSLFNXSZDQGTechnical Data Category DataGC-1412D Graco Ohio Standard Warranty For Graco Canada Customers