Graco Inc GC-1412 NqreWrGlvhqjdjhWkhFdwdo\Vw, Do\VwÀrzvEdfnWrWkhErwwoh

Page 21

Start-Up

SSP-160-01

9a. Pull and rotate Pivot

NQREWRGLVHQJDJHWKHFDWDO\VW

drive arm.

E Turn the slave pump yellow ball valve to the open position.

c. Hand prime the pump until a steady stream of cat-

DO\VWÀRZVEDFNWRWKHERWWOH

d.Close the ball valve. Hand

VWURNHWKHSXPSXQWLOLWGHYHO

opes 300-400 PSI (21-28 bar).

If you are using the optional Formula gun set the trigger air regulator to 100 PSI (7 bar). The trigger

air IS NOT to exceed 100 PSI (7 bar).

10.Trigger the Gun into a container until all the air is

purged from the resin side of the system. It may be

QHFHVVDU\WR+DQGVWURNHWKH&DWDO\VW3XPS

several times while the gun is triggered to positively deliver a steady stream of catalyst. Let go of the

WULJJHUDQGKDQGVWURNHSXPSDJDLQWRGHYHORS

300-400 PSI (21-28 bar). “STOP”

a.6ROYHQWÀXVKWKHJXQ³6723´

E Once primed, increase the resin PSI until a desired spray pattern is achieved.

c. After all pressure adjustments have been completed, a

¿QDOVSUD\WHVWVKRXOGEHPDGH6SUD\DWHVWVKRW

sample on a clean piece of paper. The shot should be

DSSUR[LPDWHO\¿YHIHHWLQOHQJWK<RXFDQQRZFKHFN

desired gel times and uniformity of curing.

d. Flush the gun thoroughly with solvent after use.

11.0DNHVXUHWKDWWKHUHVLQSXPSUHFLUFXODWLRQYDOYH

LV³RII´DQGWKDWWKHE\SDVVKRVHLVLQEDFNLQWKH

the drum. Adjust the resin pump regulator to 20 PSI (1.4 bar) the pump will start to slowly cycle. Allow the pump to “load” the cycle rate should slow indicating the pump is primed. Close the recirculation valve.

Recirculation Valve

Resin Pump Regulator

Do not exceed 20 PSI (1.4 bar) pressure on the Material

5HJXODWRUXQWLOVWHDG\PDWHULDOÀRZKDVEHHQHVWDEOLVKHG

GC-1412D

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Internal Chop System GC-1412D Contents ‡.HHSDZRUNLQJ¿UHHWLQJXLVKHULQWKHZRUNDUHD SUHYHQW¿UHDQGHSORVLRQSkin Injection Hazard Comply with all applicable safety regulationsMethyl Ethyl Ketone Peroxide Mekp Important Safety InformationPolyester Resins and Gel-Coats Spraying and Lamination OperationsGrounding For detailed grounding instructions of all equipmentWKHZRUNDUHD Tools Required Set-Up 6WDQGDUGZUHQFK VRFNHWVHW Loosen clamp bolts to expose pump mountingPump Install tubing p/n 9704-11 from the catalyst jug to Proper sized wrenches, carefully tighten the compresVLRQQXWWRORFNGRZQWKHWXELQJ Set-Up Lay all of the hoses out straight Indy Chopper Gun OptionThem with tape about every 2 feet 11. a. Attach the hoses to the gunYellow Solvent Hose p/n ODFN0DWHULDOKLS+RVHWKHERRPZLWKELQGLQJVWUDSV From Spool To GunTo Boom Formula Chopper Gun Option 16. a. Attach the hoses to the gun 6HFXUHWKH¿YHKRVHVWRWKH Attach the hoses to the unit as shown 1XPEHU Part Description Qty7RUHOLHYHÀXLGDQGDLUSUHVVXUHV Pressure Relief ProcedureSystem Start-Up Instructions Start-UpNQREWRGLVHQJDJHWKHFDWDO\VW DO\VWÀRZVEDFNWRWKHERWWOHVWURNHWKHSXPSXQWLOLWGHYHO Shut-Down Instructions Shut-downFormula Gun WULJJHUORFNSQ0DWHULDO6SUD\1ROHV PartsStandard Equipment Part Description6XE$VVHPEO\UDZLQJV Filter Options Part Description GAM-268-01 Material Pick-Up Kit Part Description QtyAir Manifold Part Description Qty 6ROYHQW7DQN Part Description QtyOptional Part Description Qty LW$VVHPEO\ +HDWHU&RQYHUVLRQ.LW$VVHPEO\ Clean pump lube cup and add fresh pump lube MaintenanceBottle Fluid Filter Assembly QVSHFWDQGFOHDQ¿OWHURQSLFNXSZDQGCategory Data Technical DataGC-1412D For Graco Canada Customers Graco Ohio Standard Warranty
Top Page Image Contents