I.C.T.C. Holdings Corporation HRO-ST3131 KEY Points Before Starting To Spray, Operation

Page 7

WARNING

If there are leaks, shut off the pump immediately and release system pressure. Follow the “Pressure Relief Procedure” then tighten connections, start the pump again and check to be sure leaking has stopped.

Always use the lowest pressure necessary to get the desired results, Higher pressures waste fluid and cause premature wear of the pump packings and spray tips.

Never allow the pump to run dry of the fluid being pumped, because a dry pump will quickly accelerate to a high speed, possibly damage itself. If the pump accelerates quickly or is running too fast, shut off pump immediately and check the fluid supply.

KEY POINTS BEFORE STARTING

TO SPRAY

1Check the hydraulic fluid level in the tank

2Check the engine oil level.

3Check the grounding of the system to prevent static sparking.

4Flush the system and test for leaks.

5Lubricate the pump with Hero piston lubricant part # 4-02-40-3PL1 in the wet cup.

6Remove and check gun filter, if used, to see that it is clean.

7Closed the prime / drain valve.

8Check the level of paint in the supply container and see that the paint has been thoroughly mixed, and if necessary, thinned.

9Keep the pump, hose and gun clean inside and outside.

OPERATION

Follow the “Pressure Relief Procedure” before operating.

FLUSHING TO CLEAN SYSTEM

Flush the pump, hose and gun with the solvent as

Recommended by your material supplier.

FLUSH THE PUMP BEFORE STARTING

1Make sure that engine is shut off.

WARNING : DO NOT INSTALL THE SPRAY TIP .

2Connect a suction hose to the pump’s fluid inlet or put in a metal pail containing a gallon of compatible sol- vents.

3Close the drain valve.

4Hold a metal part of the spray gun firmly against the side of a grounded metal pail and hold the trigger open.

5Turn the switch to the on position and start.

6Very slowly turn the pressure regulator clockwise until the pump starts about 100 P.S.I.

7Cycle the pump slowly until all air is pushed out, and fluid is flowing in a steady stream.

8Release the spray gun trigger and engage the safety latch in the “Lock” position and carefully

check all connections in the system for leaks.

9Follow the “Pressure Relief Procedure” and then install the spray tip in the gun.

HRO-ST3131

Page 7

Mar 8, 2004

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Do not Attempt to Operate this Machine Until YOU have Read R.O. Warranty Unit Layout Spray GUN Safety Warning GAS / Hydraulic Powered Airless Spray PumpsFire or Explosion Warning Pressure Relief ProcedureHose Safety Equipment PressureAirless Spray Technique Grounding SafetyMoving Parts Safety Warning InstallationKEY Points Before Starting To Spray Flushing to Clean SystemOperation Maintenance Setting UP to SprayShutdown for Storage Trouble Possible Cause Remedy Trouble ShootingSpray Starting and Adjusting Flushing Procedure R.O. Industries 2719 Lake City WAY BURNABY, B.C Canada

HRO-ST3131 specifications

I.C.T.C. Holdings Corporation's HRO-ST3131 is a state-of-the-art solution designed for organizations looking to streamline their operational processes through advanced technology. This innovative system integrates cutting-edge features and technologies that cater to a wide array of industries, enhancing efficiency and productivity.

One of the standout characteristics of the HRO-ST3131 is its user-friendly interface, which facilitates easy navigation and operation. Designed with stakeholders of all technical backgrounds in mind, the system reduces the learning curve for new users, allowing for quicker onboarding and adaptation within organizations. This feature is particularly beneficial for companies that value agility and responsiveness in a rapidly changing business environment.

The HRO-ST3131 incorporates robust data management and analytics capabilities, empowering users to make informed decisions based on real-time data. By utilizing advanced algorithms and machine learning techniques, organizations can gain valuable insights into their operational performance, identify trends, and forecast future needs. This data-centric approach allows for more strategic planning and can significantly enhance overall business outcomes.

In terms of connectivity, the HRO-ST3131 supports a variety of communication protocols, which ensures seamless integration with existing systems and software platforms. This versatility is crucial for organizations that rely on multiple technologies to function effectively. The system also features cloud integration, which facilitates easy access to data from anywhere, thereby fostering collaboration and flexibility among teams.

Security is another key feature of the HRO-ST3131. With built-in encryption and access control mechanisms, the system ensures that sensitive information is protected from unauthorized access and breaches. As data privacy becomes increasingly important for businesses, the HRO-ST3131 addresses these concerns with a comprehensive security framework.

Finally, the HRO-ST3131 is designed for scalability, allowing organizations to expand their operations without overhauling their existing infrastructure. Whether a company is experiencing rapid growth or simply needs to adapt to changing market conditions, the HRO-ST3131 offers the flexibility and functionality needed to succeed. Overall, I.C.T.C. Holdings Corporation's HRO-ST3131 stands out as a forward-thinking solution that not only meets current demand but is also poised to support future advancements in organizational technology.
Top Page Image Contents