Carrier 33ZCSECTRM, 33ZCFANTRM Default Value Normal, Options Service Configuration Screen

Start Value:	Units	F (C)
	Range	40 to 125
	Default Value	80

Ducted Heat — The Ducted Heat configuration is used to con- figure the terminal for ducted heat. If a local heat source is in the duct and requires airflow to provide heat, set the Ducted Heat configuration for yes.

Ducted Heat	Range	No/Yes
	Default Value	Yes

Maximum Duct Temperature — This configuration is used to configure the maximum supply-air temperature desirable for heating the space. This will cause the heat to be modulated or cycled using this value as the maximum temperature of the air to be supplied.

Maximum Duct
Temperature:	Units	F (C)
	Range	40 to 200
	Default Value	110

Number of Electric Stages — This configuration is used to define the number of stages of electric heat controlled by the zone controller.

Number of
Electric Stages: Range	1 to 3
Default Value	1

Heat On Delay — The Heat On Delay configuration is used to define a delay from the time a parallel terminal fan is started until the heat is activated.

Heat On Delay: Units	minutes
Range	1 to 60
Default Value	2

Fan Off Delay — The Fan Off Delay configuration is used to define a delay time. The delay time is from when the heat is de- activated (in a parallel terminal) until the parallel fan is deacti- vated. This allows the fan to circulate air and remove the resid- ual heat from the heat source.

Fan Off Delay: Units	minutes
Range	1 to 15
Default Value	2

Two-Position Heat Logic — This configuration is used for controlling a normally closed or normally open valve for hot water. Use normal logic if the valve is normally closed. Use in- verted logic if the valve is normally open.

Two Position
Heat Logic:	Range	Normal/Invert
	Default Value	Normal

Space Temperature Trim — This configuration is used to trim a space sensor which might need calibration. For example, if the temperature displayed is two degrees above the value mea- sured with calibrated test equipment, input a value of –2.0.

Space Temperature
Trim:	Units	delta F (delta C)
	Range	–9.9 to 9.9
	Default Value	0.0

Supply Air Temperature Trim — This configuration is used to trim a supply air sensor which might need calibration. For example, if the temperature displayed is two degrees above the value measured with calibrated test equipment, input a value of

–2.0.

Supply Air Temperature
Trim:	Units	delta F (delta C)
	Range	–9.9 to 9.9
	Default Value	0.0

→Remote Contact Config — The remote timeclock contact in- put can be configured as a normally open or normally closed contact. When the timeclock input is ‘On’ the zone will follow it’s local occupancy schedule. When the timeclock input is ‘Off’ the zone will be forced into unoccupied state.

Remote Contact
Config:	Range	Close/Open
	Default Value	Close

OPTIONS SERVICE CONFIGURATION SCREEN — The Options Service Configuration screen is used to configure the service options of the air terminal controller. See Table 11.

Occupancy Schedule Number — The Occupancy Schedule Number defines what Occupancy schedule the zone controller will use. Occupancy Schedule 64 is a local schedule. Occupan- cy Schedules 65 to 99 are global schedules.

Occupancy Schedule
Number:	Range	64 to 99
	Default Value	64

Global Schedule Master — The Global Schedule Master con- figuration allows the Occupancy Schedule to be used as a Glo- bal Schedule Master (Occupancy Schedules 65-99).

Global Schedule
Master:	Range	No/Yes
	Default Value	No

Table 11 — Options Service Configuration Screen

DESCRIPTION	DEFAULT	POINT NAME
Occupancy Schedule Number	64	SCH
Global Schedule Master	No	GSM
Override	00:00	OVR
Broadcast Acknowledge	No	BCACK
Set Point Group Number	0	SETT
Global Set Point Master	No	GSTM
Maximum Offset Adjust	2 F	LIMT
Control Options	0	CTLOPT
Humidity
Proportional Gain	1.5	KP
Integral Gain	0.30	KI
Maximum Output Value	100.0 cfm	MAXOUT
Air Quality
Proportional Gain	0.10	KP
Integral Gain	0.03	KI
Maximum Output Value	100.0 cfm	MAXOUT
AQ Low Voltage	0.0	AQINLO
AQ High Voltage	10.0	AQINHI
AQ Low Reference	0 ppm	AQLO
AQ High Reference	2000 ppm	AQHI

41 801