WARNING! Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap. Without capin place, battery could short circuit causing fire or burns or damage to battery.
SAFETY WARNINGS AND INSTRUCTIONS: CHARGING THE BATTERY
1.This manual contains important safety and operating instructions.
2.Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
3.
CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs. Other types of batteries may burst causing personal injury and damage.
4.Do not expose charger to rain or snow.
5.Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock, or injury to persons.
6.To reduce risk of damage to electric plug and cord, pull by plug rather than cord when dis- connecting charger.
7.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise sub- jected to damage or stress.
8.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.
a.
b.An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
NAMEPLATE RATING AMPS – 0 – 10.0 |
| |||||
Total Extension Cord Length (ft) | 25 | 50 | 75 | 100 | 125 | 150 |
Wire Gauge | 18 | 18 | 16 | 16 | 14 | 14 |
9.Use only the supplied charger when charging your tool. The use of any other charger could damage the battery or create a hazardous condition.
10.Use only one charger when charging.
11.Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.
12.DO NOT incinerate the battery packs even if they are severely damaged or completely worn out. The batteries can explode in a fire.
13.A small leakage of liquid from the battery cells may occur under extreme usage, charg- ing or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:
a.Wash quickly with soap and water.
b.Neutralize with a mild acid such as lemon juice or vinegar.
c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a
CHARGING THE POWER PACK
THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1.Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
2.Slide the charger onto the battery pack as shown in Figure 1 and let it charge initially for 9 hours. After the initial charge, under normal usage, your power pack should be fully charged in 3 to 6 hours.
3.Remove pack from the charger and place in product (Figure 2). NOTE: To remove the battery from the product, press down on the release button on the back of the battery (Figure3) and pull out.
IMPORTANT CHARGING NOTES
1.After normal usage, your power pack should be fully charged in 3 to 6 hours. If the power pack is
2.DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This is important and will prevent serious damage to the power pack. Longest life and best per- formance can be obtained if power pack is charged when air temperature is about 75°F.
3.While charging, the charger may hum and become warm to touch. This is a normal con- dition and does not indicate a problem.
4.If the power pack does not charge properly— (1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and temperature are
OK, and you do not get proper charging, take or send the power pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages.
5.The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its power pack in a depleted condition.
6.To prolong power pack life, avoid leaving the power pack on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall power pack life.
7.When the battery is inserted into the charger, the red “Charging Indicator” light will come on indicating that there is contact between the battery and charger. The light will stay on as long as the battery is in the charger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to a different color when the charging cycle is complete.
8.The power pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries.
OPERATION
FITTING AND REMOVING INTERCHANGEABLE TOOL HEADS
NOTE: Ensure the forward / reverse switch is in the center (lock off) position.
To install a tool head, align the arrows on both the tool head and the power unit and insert the head until it clicks into place as shown in Fig. 4. To remove, press the release button and pull the tool head off. Remove battery from power unit and all accessories from tool heads before removing or installing.
NOTE: The main body unit (type 2) is equipped with a directional mechanism which allows it to fit a circular saw tool head and a router tool head.
VARIABLE SPEED CONTROL
The power unit has a variable speed switch. The more the trigger switch is depressed the higher the speed of the attached head. Note: Trigger does not work when there is no head attached.
TRIGGER SWITCH & FORWARD / REVERSE / LOCK BUTTON
A forward / reverse control button determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward / reverse control button as shown in Figure 5. To select reverse, depress the forward / reverse control button the opposite direction. The center position of the control button locks the tool in the off position. Note: For greatest efficiency, always use sander and saw in for- ward position.
DRILLING
Note: Ensure the forward / reverse switch is in the center (lock off) position.
KEYLESS CHUCK
To insert a drill bit or other accessory:
1.Grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction, (Fig. 6).
2.Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.
TORQUE CONTROL
The torque adjustment collar shown in Fig. 5 has 24 settings. There are 23 screwdriving set- tings and a drilling setting which is represented by the drill bit symbol. For screwdriving pro- ceed as follows:
Set the torque adjustment to position “1”. Fit and tighten the first screw. If the clutch of your drill starts to ratchet before the screw is correctly seated, rotate the adjustment collar as nec- essary, until the clutch slips when the head of the screw is flush with the surface of the mate- rial. Use this torque setting for the rest of the screws.
DRILLING TIPS
Always remove batteries from drill when attaching or removing accessories. When using a keyless chuck, hand tighten firmly.
•Use sharp drill bits only.
•Support and secure work properly, as instructed in the Safety Instructions.
•Use appropriate and required safety equipment, as instructed in the Safety Instructions.
•Secure and maintain work area, as instructed in Safety Instructions.
•Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.
•Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.
•Hold the drill firmly to control its twisting action..
•DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.
•Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.
•Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jam- ming.
•Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The lubricants that work best are sulphurized cutting oil or lard oil. Bacon grease will also serve.
•When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out fre- quently to clear chips from the flutes.
•Make sure switch turns drill on and off.
WARNING: It is important to support the work properly and to hold the drill firmly to pre- vent loss of control which could cause personal injury.
SAWING
Note: Ensure the forward / reverse switch is in the center (lock off) position.
INSTALLING BLADES
Your jig saw uses the Quick Clamp™ blade changing system. To install a blade, lift the Quick Clamp™ lever (Figure 7). Insert the saw blade shank fully into the blade clamp. Release the lever and the blade will be clamped securely in place. The back of the blade should be just touching the roller support guide. Ensure the blade teeth are facing forward.
ROLLER SUPPORT GUIDE
The roller support guide on your jig saw improves its performance when cutting tough mate- rials by adding support to the blade. Lubricating the guide roller with a drop of oil from time to time will extend the roller life.
USING THE JIG SAW
The jig saw is equipped with a lock off switch. To start the saw, first depress the lock off but- ton shown in Fig. 8 followed by the trigger switch (Fig.4) You can then release the lock off button.
SHOE ADJUSTMENT FOR ANGLE CUTTING
The shoe plate can be angled to 45º on one side. To do this, first loosen the screw at the base of the saw head until the shoe can freely move. The shoe should then be repositioned in the forward slot and the screw retightened. To reset the shoe to a square cut, loosen the clamp screw and move the shoe so that the clamp screw is against the rear of the slot. Retighten clamp screw.
GENERAL CUTTING
Be sure material is firmly secured. Don’t attempt to turn on the unit when blade is against material to be cut. This could stall the motor. Place front of shoe on material to be cut and hold jig saw shoe down firmly against the work surface while cutting. Don’t force the tool; let the blade cut at its own speed. Whenever possible, clamp or support work close to the line of cut; when the cut is completed, shut off power and lay the tool aside before loosening the work.
METAL & PLASTIC CUTTING
In cutting thin gauge sheet metals, it is best to clamp wood or plywood to the bottom of the metal sheet; this will insure a clean cut without the danger of vibration or tearing of metal. Use a
Cutting thin metal will take longer than cutting relatively thick wood so do not be tempted to speed up the process by forcing the saw. Spread a thin film of cutting lubricant along the cut- ting line, (any light weight oil). Use low speeds for cutting metals, plastics and composition tile. When cutting laminated plastic, place the finished side down and use a fine tooth hollow ground blade.
POCKET CUTTING
•Measure the surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front edge of the shoe sits firmly on the work surface.
•Switch the tool on and allow it to attain maximum speed.
•Grip the handle firmly and lower the back edge of tool until the blade cuts smoothly into material. Always be sure blade reaches its complete depth before starting to cut.
SANDING
Note: Ensure the forward / reverse switch is in the center (lock off) position.
ATTACHING SANDPAPER
The sander uses
Ensure the abrasive evenly overlaps the base. Never use your sander without an abrasive or accessory. The abrasive supplied with your tool has two replacement tips. This design allows you to interchange and or rotate the diamond tips. To rotate the tip, remove it from the pad, rotate it 180º and press it back on the hook base. Note: Remove the two replacement tips from the abrasive before use, these can be used later when the original diamond tip wears.
SANDING LEAD BASED PAINT
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analy- sis, we recommend the following precautions when sanding any paint:
PERSONAL SAFETY
•No children or pregnant women should enter the work area where the paint sanding is being done until all cleanup is completed.
•A dust mask or respirator should be worn by all persons entering the work area. The filter should be replaced daily or whenever the wearer has difficulty breathing.
•Note: Only those dust masks suitable for working with lead paint dust and fumes should be used. Ordinary painting masks do not offer this protection. See your local hardware dealer for the proper (NIOSH approved) mask.
•NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work area where dust would settle on them.
ENVIRONMENTAL SAFETY
•Paint should be removed in such a manner as to minimize the amount of dust generated.
•Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness.
•Sanding should be done in a manner to reduce tracking of paint dust outside the work area.