DeWalt DWD024 manual Voltage Volts Total length of cord in meters m

Page 4

English

•Wear safety goggles or other eye protection.Drilling operations cause chips to fly. Flying particles can cause permanent eye damage.

•Bits and tools get hot during operation. Wear gloves when touching them.

•Keep handles dry, clean, free from oil and grease. it is recommended to use rubber gloves. This will enable better control of the tool.

•An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Voltage (Volts)

Total length of cord in meters (m)

 

 

 

 

 

 

 

 

120

- 127V

0 - 7

 

7 - 15

15 - 30

 

30 - 50

 

 

 

 

 

 

 

220

- 240V

0 - 15

 

15 - 30

30 - 60

60 - 100

 

 

 

 

 

Rated Ampere

Minimal cross-sectional area of the

range

 

cord in meters (mm2 )

 

0

- 6A

1.0

 

1.5

1.5

 

2.5

 

 

 

 

 

 

 

 

6

- 10A

1.0

 

1.5

2.5

 

4.0

 

 

 

 

 

 

 

 

10

- 12A

1.5

 

1.5

2.5

 

4.0

 

 

 

 

 

 

 

12

- 16A

2.5

 

4.0

Not Recommended

 

 

 

 

 

 

 

 

WARNING: Always use eye protection.All users and bystanders must wear eye protection that conforms to ANSI Z87.1.

WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING:ALWAYS use safety glasses.Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

•ANSI Z87.1 eye protection (CAN/CSA Z94.3),

•ANSI S12.6 (S3.19) hearing protection,

•NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Manual DE Instrucciones Manual DE Instruções Definitions Safety Guidelines General Power Tool Safety WarningsWork Area Safety Electrical SafetySpecific Safety Rules Safety Warnings for DrillsPower Tool USE and Care ServiceVoltage Volts Total length of cord in meters m Description FIG Assembly and Adjustments Mode Selector FigSetting the Drilling Depth Fig Side Handle FigTo Insert a Drill BIT or Other Accessory Keyed Chuck Installation FIGKeyed Chuck , 4 OperationTrigger Switch Fig Proper Hand PositionDrilling Variable SpeedMaintenance Cleaning AccessoriesMotor Brushes LubricationSpecifications Seguridad DEL Área DE Trabajo Definiciones Normas De seguridadSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaAdvertencias de seguridad para taladros Normas Específicas DE SeguridadMantenimiento Ténsion Volts Longitud del cable en metros m Descripción FIG Montaje Y Ajustes Mango lateral FigPalanca de avance y retroceso Fig Selector de modalidad FigSelección de la profundidad de taladrado Fig Mandril con llave , 4Funcionamiento Gatillo conmutador FigPosición debida de las Manos Fig TaladradoMantenimiento Cepillos del motorTaladrado EN Metal Taladrado EN MaderaLubricación LimpiezaAccesorios Capacidades Máximas RecomendadasDefinições Diretrizes De Segurança Guarde Todos OS Avisos E Instruções Para Futuras ConsultasSegurança DA Área DE Trabalho Segurança ElétricaSegurança Pessoal Utilização E Manutenção DE Ferramentas ElétricasPrecauções de segurança para furadeiras Regras DE Segurança EspecíficasAssistência Descrição Montagem E Ajustes Empunhadura lateral FiguraUSO Devido DA Ferramenta Como Ajustar a Empunhadura LateralSeletor de modo Figura Alavanca Avançar/Recuar FiguraComo determinar a profundidade de perfuração Figura Como Operar a Ferramenta Mandril com chave Figuras 1, 4Interruptor tipo gatilho Figura Perfuração Como segurar Corretamente a Ferramenta FiguraPerfuração EM Metal Manutenção Escovas do motorLubrificação LimpezaEspecificações Capacidades Máximas RecomendadasPage AUG10 Part No. N086627 DWD024

DWD024 specifications

The DeWalt DWD024 is a powerful and versatile electric drill that is designed to meet the demands of both professionals and DIY enthusiasts. It features a robust 650-watt motor that delivers impressive performance for various drilling tasks. With a no-load speed of up to 2,500 RPM, this drill is capable of handling a variety of materials, including wood, metal, and plastic, making it a perfect choice for a wide range of applications.

One of the standout features of the DWD024 is its 13mm keyless chuck, which allows for quick and easy bit changes. This convenience is particularly beneficial when switching between different drilling tasks, as it saves time and reduces frustration. The keyless chuck also ensures a secure grip on the drill bits, enhancing safety during use.

The DWD024 incorporates a variable speed control, enabling users to adjust the speed according to the specific requirements of the task at hand. This feature gives users greater control, particularly when working with delicate materials or when precision is essential. Additionally, the drill has a forward and reverse switch, allowing for both drilling and screw-driving applications.

The ergonomic design of the DeWalt DWD024 enhances comfort during extended use. It is equipped with a rubber grip that provides a secure hold, minimizing fatigue and slipping. The lightweight construction of the drill also contributes to its user-friendly nature, making it easy to maneuver and control.

Another notable characteristic of the DWD024 is its built-in depth stop, which allows users to set and maintain accurate drilling depths. This is particularly useful for repetitive tasks where consistency is key. The drill's durable construction ensures longevity, making it a reliable tool for demanding job sites.

The DWD024 is also designed with safety in mind. It features a two-finger trigger switch for better control and a lock-on button, which can be engaged for continuous use without needing to hold the trigger down. This feature is especially useful for prolonged tasks, providing added convenience for the user.

Overall, the DeWalt DWD024 is a well-rounded electric drill that combines power, versatility, and user-friendly features. Whether you are a professional tradesperson or a DIY hobbyist, this drill is sure to meet your needs and exceed your expectations. With its solid performance and thoughtful design, the DWD024 stands out as a reliable tool for all your drilling needs.
Top Page Image Contents