ACCESSORY ORDER FORM for illustratiorts of
ttte acces_orie-J available. These accessories
may be found at your local hardware, hobby or home center dealers.
Collets (_=====__
If you expect to use a variety of accessories,
we recommend that in the beginning you
purchase a corn plate set of four cotlets. Store
these so that you will have the proper size of
toilet for any accessory or drill bit you want to
use. Currently, the 1/8" and 3/32 n collet_
accommodate all of the available Dremel accessories.
Mandrels
A mand | rei | is a shank with | a threaded | or screw |
head, | | and | mandrels | are | required | | when | you |
use | polishing | accessories, | | cutting | wheels, |
sanding | | discs, | and | polishing | points. | The |
reason | mandrels | are | used | is that | sanding |
disc.s, cutting wheels and similar accessories |
must | | be replaced | frequently. | The | mandrel | is |
a permanent | shank, | allowing | you | | to replace |
only | the | worm | head | when | necessary, | thus |
saving | | the expense | of | replacing | | the shaft |
each | time. | | | | | | | | |
Structured Tooth
Tungsten Carbide Cutters
Fast cutting, needle-sharp teeth for greater
material removal, minimum loading. Use on
fiberglass, wood, plastic, epoxy and rubber.
Aluminum Oxide Grinding Stones
Round, pointed, flat -- you name the shape
and there is one available in this category.
These are made of aluminum oxide and cover
virtually every possible kind of grinding
application. Use them for sharpening lawn
mowers blades, screwdriver tips, knives, scissors, chisets and other cutting tools. Use
to remove flash from metal castings, debur-
ring any metal after cutting, smoothing
welded joints, grinding off rivets and removing
rust. In macnineshops, high soeed drtllsand
cutters normally are ground with aluminum oxide wheels.
furniture finishing. In addition, there is the drum sander, a tiny drum which fits into the
Moto-Tool and makes it possible to shape
wood, smooth fiberglass, sand inside curves and other difficult places, and other sanding jobs. You replace the sanding bands on the
drum as they become worn and lose their grit. Bands come in fine and coarse grades.
Wire Brushes
Three different shapes of wire brushes are
available. For best results wire brushes
should be used at speeds not greater than
15,000 RPM. They remove rust from tools
and other metal surfaces, and clean and
burnish metal parts. Use for such jobs as
cleaning electrical connections to assure good conduction.
Bristle Brushes
These are excellent cleaning tools on silverware,
Screw Mandrel No. 401
This is a screw mandrel used with the felt;
polishing tip and felt polishing wheels
Small Screw Mandrel No. 402
This is a mandrel with a small screw at its tilS, and is used with emery cutting wheels, sanding
discs, and polishing wheels.
Threaded Tip Mandrel No. 424
This is a mandrel with threaded tip which
threads into the polishing point accessory No. 427.
Silcon Carbide Grinding Stones
Tougher than aluminum oxide points, these
are made especially for use on hard materials
such as glass and ceramics. Typical uses
might be the removal of stilt marks and
excess glaze on ceramics and engraving on glass.
Diamond Wheel Points
Excellent for fine detail work on wood. jade,
ceramic, glass and other hard material. Bits
are covered with diamond particles. 3/32 ° shanks.
jewelry and antiques. The three shapes make
it possible to get into tight corners and other difficult places. Bristle brushes can be used
with polishing compound for faster cleaning or polishing.
When using the steel saws
(Nos. 400, 406) or cutoff
wheels (Nos, 409, 420, 426) always have the
work securely clamped. Never attempt to hold the work with one hand while using
either of these accessories. The reason is that these wheels will grab if they become slightly canted in the groove, and can kick-
back causing loss of control resulting in serious injury. Your second hand should be used to steady and guide the hand holding
the tool. When a cutoff wheel grabs, the wheel itself usually breaks. When the steel
High Speed Cutters
Available in 24 shapes, high speed cutters
are used in carving, cutting, and slotting in
wood, plastics, and soft metals such as
aluminum, copper, and brass. These arethe
accessories to use for freehand routing or
carving in wood or plastic, and for precision cutting.
Tungsten Carbiae Cutters
These are tough, long-lived cutters for use on
hardened steel, fired ceramics, and other very
hard materials. They can be used for engraving
on tools and garden equipment.
Small Engraving Cutters
This group has a wide variety of sizes and
shapes, and are made for intricate work on
ceramics (greenware), wood carvings, jewelry,
and scrimshaw. They often are used in making
complicated printed circuit boards. They
should not be used on steel and other very
Polishing Accessories
These include an impregnated polishing point
and an impregnated polishing wheel for
bringing metal surfaces to smooth finish; a
felt polishing tip and felt polishing wheel, and
cloth polishing wheel, all used for polishing
plastics, metals, jewelry small parts. Also
included in this group is a polishing compound (No. 421) for use with the felt and cloth
polishers.
Polishing points make a very smooth surface,
but a high luster is obtained using felt or cloth
wheels and polishing compound.
No polishing compound is needed when using the 425 Polishing Wheel, 427' Polishing point.
Aluminum Oxide Abrasive Wheels
Use to remove paint, deburr metal, polish
stainless steel and other metals. Available in
fine and medium grits.
saw wheel grabs, it may jump from the
groove and you could lose control of the tool.
Cutting Wheels
These are thin discs of emery or fiberglass
used for slicing, cutting off and similar
operations. Use them for cutting off frozen
bolt heads and nuts, or to reslot a screw head
which has become so damaged that the
screwdriver won't work in it. Fine for cutting
BX cable, small rods, jubing, cable and
cutting rectangular holes_ln sheet metal.
