Carrier 37HS specifications Air Series of Units of the Same Size and Capacity

Page 35

Fig. 22 Ð Air Series of Units of the Same Size and Capacity

FLEX DUCT IN AIR SERIES Ð Flexible duct is often used in air series to connect Moduline units. In calculating pres- sure requirements for units in air series, use the following guidelines:

1.For close-coupled units (either continuous diffuser or units in adjoining ceiling modules) where the ¯exible duct used is 6 to 8 in. in length, add 0.1 in. wg to unit requirement for minimum static pressure at control unit (Table 10).

For example, consider three 37HS2 units in air series, in adjoining modules, with 200 cfm per unit (Fig. 23). The minimum static pressure for multiple units is equal to 0.75 in. wg (from Table 10). Adding 0.1 in. wg for ¯exible duct, the total pressure downstream of run-out duct equals 0.85 in. wg.

2.For units in air series with extended ¯exible duct lengths, add DP from Table 11.

For example, consider four 37HS2 units in air series, 200 cfm per unit (Fig. 24). The units are in alternate series modules; 8-in. duct; 9- x 9-in. plenum. The

minimum static pressure for multiple units is equal to 0.75 in. wg. Three lengths of ¯ex duct at 4.5 ft equal 13.5 ft. From Table 11, read with 8-in. duct diam, DP is equal to

0.16in. wg for each 10 ft. of ¯ex duct. Therefore, for

13.5ft, DP is equal to 0.16 + 0.06 in. wg. The total DP downstream of run-out duct is equal to 0.75 + 0.22 = 0.97 in. wg.

3.Flexible duct, unsupported, tends to sag; this de¯ection increases the pressure drop. Whenever possible, support

the duct with wire between connections. Sagging will in- crease the DP as much as 0.06 in. wg in a 10-ft length; therefore rigid duct is recommended for lengths greater than 5.5 ft.

4.The use of ¯exible duct in air series run-out when 90 de- gree turns are required will also add DP. Table 12 pro- vides the additional pressure drop.

For example, refer to Fig. 25. The ``straight'' line DP is equal to 0.97 in. wg. If a bend is added to the run-out, the total pressure drop becomes:

0.97+ 0.16 = 1.13 in. wg.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Introduction Contents37HS Unit With VAV Controls Building Load CalculationEstimating Block Load Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 35BD Heating Slot Boot Diffuser Director Diffuser Location Guidelines Terminal Selection LayoutOptimum Outlet Discharge Single Moduline Unit Connected to Supply Duct Diffuser Locations for Preferred 2-Way or One-Way Blow Recommended Maximum Cfm Per TerminalAir Throw Data Ð Way and 1-Way Director, 3-Slot Diffusers Consider Unit Combinations And Run Run-Out Duct for Single Moduline Unit 37HS1 Units in Air Series 37HS1 Units in Air Series 37HS2 Units in Air Series 37HS2 Units in Air Series 37HS4 Units in Air Series 37HS4 Units in Air Series Air Series of Units with Different Capacities Air Series of Units of the Same Size and Capacity Units in Adjoining Modules Additional DP for Flexible Duct with 90-Degree BendMaximum Number of Units in an Air Series on One Controller Flexible Duct Used with 90-Degree BendLocation of Volume Controller On Single Unit Incorrect Layout of Moduline Units with Controls Corrected Layout Shows the internal components of the Moduline unit Moduline ValveBellows and Unit Air Valve Arrangement Cross Section of 37HS Moduline Air Terminal High and Low Pressure Pick-Up Tubes Control Applications37HS Control Components Wall-Mounted Thermostat Constant Volume Control Arrangement Cooling/Heating Wall Thermostat VAV Control Arrangement with Electric Heat Interlock Control Index Control Selection37HS Control Combinations Heating & Cooling Electric Changeover HEATING/COOLING Control Operating Sequences Variable Volume Controls Schematic Page Page Page Location of CV Unit for Warm-Up Application Page Page Page System-Powered Controls with Electric Interface Page Page Page Connection for Electric Interlock System-Powered Controls with Pneumatic Interface Piping Diagram, no Conguration Pneumatic Warm-Up Maximum Air¯ow Settings Airflow AdjustmentMultiple Unit Air¯ow Variation HK08ZZ030Moduline Diffuser Mixing Room Air and Primary Air AIR DistributionTypical Room Air Distribution Pattern Slot Openings in Standard and Optional Diffusers Standard Diffusers for 37HS1 Standard Diffusers for 37HS2 Standard Diffusers for 37HS4 Model Type Optional Diffusers for 37HS1Optional Diffusers for 37HS2 Optional Diffusers for 37HS4 Air Throw Data Ð Way and 2-Way Blow, 2-Slot Diffusers Page Copyright 1991 Carrier Corporation

37HS specifications

The Carrier 37HS is a cutting-edge heating, ventilation, and air conditioning (HVAC) solution designed to deliver exceptional performance and energy efficiency for residential and commercial applications. This unit is particularly favored for its advanced features and reliable operation, making it a popular choice among homeowners and building managers alike.

One of the standout characteristics of the Carrier 37HS is its high Seasonal Energy Efficiency Ratio (SEER), which indicates its ability to provide effective cooling while minimizing energy consumption. This makes it not only cost-effective but also an environmentally-friendly choice, helping to reduce the overall carbon footprint. The unit is equipped with state-of-the-art inverter technology, which allows it to adjust its cooling capacity to match the current demand, thus enhancing comfort while optimizing energy use.

The Carrier 37HS incorporates a high-efficiency scroll compressor that operates quietly and efficiently. This technology enhances the unit's reliability and longer service life while ensuring minimal noise levels during operation, making it suitable for residential settings where tranquility is paramount.

A significant feature of the 37HS is its variable-speed fan system, which enables gradual adjustments in airflow to maintain a consistent and comfortable indoor environment. This not only contributes to enhanced comfort but also reduces wear and tear on the system, further extending its longevity.

Moreover, the Carrier 37HS is designed with advanced air filtration capabilities, utilizing multi-stage filters that capture airborne particles, allergens, and pollutants. This results in improved indoor air quality, making it an ideal choice for those with allergies or respiratory issues.

The unit also boasts user-friendly smart controls, allowing homeowners to monitor and adjust settings remotely via a smartphone app. This feature adds convenience and assists in energy management, ensuring that users can optimize their HVAC system even when they are away from home.

In summary, the Carrier 37HS stands out for its exceptional energy efficiency, quiet operation, advanced technology, superior air filtration, and modern smart controls. These features collectively make it a prime solution for those seeking a reliable HVAC system that delivers both comfort and savings, while also contributing positively to environmental sustainability. Whether for a residential setting or a commercial establishment, the Carrier 37HS is engineered to meet a variety of climate control needs with excellence.
Top Page Image Contents