Ryobi HP1202M, HP962 manual Specific Safety Rules AND/OR Symbols, Tool Use and Care, Service

Page 3

GENERAL SAFETY RULES

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

Do not force tool. Use the correct tool for your appli- cation. The correct tool will do the job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is danger- ous and must be repaired.

Disconnect battery pack from tool before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may create a risk of injury when used on another tool.

Service

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a tool, use only identical replace- ment parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury.

SPECIFIC SAFETY RULES AND/OR SYMBOLS

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Additional Rules For Safe Operation

Know your power tool. Read operator's manual care- fully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in length. A cord exceeding 100 feet is not recom- mended. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

Important Rules for Battery Tools

Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operat- ing condition. Be aware of possible hazards when not using your battery tool or when changing acces- sories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not place battery tools or their batteries near fire

or heat. This will reduce the risk of explosion and possibly injury.

WARNING:

Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemical. If exposed, flush with water immediately.

Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric shock.

For best results, your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F. Do not store outside or in ve- hicles.

Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious personal injury.

Page 3

Image 3
Contents Save this Manual for Future Reference Model HP962 Model HP1202MThank YOU for Buying a Ryobi Cordless DRILL-DRIVER Table of Contents General Safety RulesTool Use and Care Specific Safety Rules AND/OR SymbolsService Important Rules for Battery ToolsImportant Safety Instructions For Charger Symbol Name DESIGNATION/EXPLANATION Symbol Meaning Safety Alert SymbolBattery SpecificationsDisposal of the Exhausted Battery Battery Pack Preparation for RecyclingTo Charge OperationKnow Your DRILL-DRIVER Charging Your DRILL-DRIVERTo Remove Battery Pack SwitchSwitch Lock To Install Battery PackKeyless Chuck Installing BitsRight Wrong ReversibleBIT Storage Screwdriving Torque AdjustmentTo Adjust Torque Removing BitsDrilling MAG Tray Model HP1202MMAG Tray Screw Holder Chuck Removal To Retighten a Loose ChuckMallet Chuck Jaws Keyless Chuck HEX KEY Batteries MaintenanceRyobi TECHNOLOGIES, INC Model Numbers HP962 / HP1202M