Ryobi HP962, HP1202M manual Important Safety Instructions For Charger

Page 4

SPECIFIC SAFETY RULES AND/OR SYMBOLS

WARNING:

A damaged battery is subject to explosion. To avoid serious personal injury, properly dispose of a damaged battery.

Important Safety Instructions For Charger

Save these instructions. This manual contains im- portant safety and operating instructions for charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, and product using battery charger. Follow- ing this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce risk of injury, charge only nickel-cadmium and nickel metal hydride type rechargeable batter- ies. Other types of batteries may burst causing personal injury and damage. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not expose charger to wet or damp conditions. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce risk of damage to charger body and cord, pull by charger plug rather than cord when discon- necting charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Following this rule will reduce the risk of serious personal injury.

An extension cord should not be used unless abso- lutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25'

50'

100'

Cord Size (AWG)

16

16

16

Note: AWG = American Wire Gage

Do not operate charger with a damaged cord or plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incor- rect reassembly may result in a risk of electric shock or fire. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Disconnect charger from power supply when not in use. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

DANGER:

RISK OF ELECTRIC SHOCK. DO NOT TOUCH UNINSULATED PORTION OF OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to cause cancer, birth defects or other repro- ductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Page 4

Image 4
Contents Model HP962 Model HP1202M Save this Manual for Future ReferenceThank YOU for Buying a Ryobi Cordless DRILL-DRIVER General Safety Rules Table of ContentsSpecific Safety Rules AND/OR Symbols ServiceImportant Rules for Battery Tools Tool Use and CareImportant Safety Instructions For Charger Symbol Meaning Safety Alert Symbol Symbol Name DESIGNATION/EXPLANATIONSpecifications Disposal of the Exhausted BatteryBattery Pack Preparation for Recycling BatteryOperation Know Your DRILL-DRIVERCharging Your DRILL-DRIVER To ChargeSwitch Switch LockTo Install Battery Pack To Remove Battery PackInstalling Bits Right WrongReversible Keyless ChuckScrewdriving Torque Adjustment To Adjust TorqueRemoving Bits BIT StorageMAG Tray Model HP1202M DrillingMAG Tray Screw Holder To Retighten a Loose Chuck Chuck RemovalMallet Chuck Jaws Keyless Chuck HEX KEY Maintenance BatteriesModel Numbers HP962 / HP1202M Ryobi TECHNOLOGIES, INC