Ryobi TS1302 manual Features

Page 8

FEATURES

KNOW YOUR MITER SAW

See Figure 2.

Before attempting to use your saw, familiarize yourself with all operating features and safety requirements.

WARNING:

Do not allow familiarity with your miter saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.

14 AMP MOTOR

Your saw has a powerful 14 amp motor with sufficient power to handle tough cutting jobs. It is made with all ball bearings.

10 in. (254 mm) BLADE

A 10 in. (254 mm) saw blade is included with your miter saw. It is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your nearest dealer.

CUTTING CAPACITIES

When the miter angle (miter table) is set at 0°:

Maximum dimensional lumber sizes: 4 x 4 2 x 6

When the miter angle (miter table) is set at 45°:

Maximum dimensional lumber size: 2 x 4

BLADE WRENCH / STORAGE AREA

See Figure 2.

A blade wrench is packed with your saw. One end of the wrench is a phillips screwdriver and the other end is a 1/4 in. (6.4 mm) hex key. Use the hex key end when installing or removing blade and the phillips end when removing or loosening screws. A storage area for the blade wrench is located behind the fence.

CARRYING HANDLE

See Figure 3.

For convenience when carrying or transporting your miter saw from one place to another, a carrying handle has been provided on top of the saw arm as shown in figure 3. To transport, turn off and unplug your saw, then lower the saw arm and lock it in the down position. Lock saw arm by depressing the lock pin. Tighten the miter lock handle. Remove the saw from the workbench or workstand. It is now ready to transport.

CARRYING HANDLE

 

LOCK

UPPER

BLADE GUARD

PIN

 

15

15

30

45

DUST BAG

FENCE

NO HANDS

ZONE LABEL

MITER TABLE

BLADEBASE

WRENCH

WRENCH

STORAGE

45

31.62

30

15

22.5

SAW ARM

SWITCH

TRIGGER

BLADE

LOWER

BLADE GUARD TABLE

EXTENSION

 

 

 

MITER TABLE

45

MITER SCALE

30

.62

 

 

31

 

22

.

5

 

 

 

 

MITER

LOCK PLATE

AREA STOP

BLOCK

TABLE

"NO HANDS ZONE"

BOUNDARY LINE

EXTENSION

 

 

Page 8

 

MITER

CONTROL ARM

LOCK HANDLE

POSITIVE STOP (S)

Fig. 2

Image 8
Contents Save this Manual for Future Reference Introduction Table of ContentsProduct Specifications Double Insulation Safety and International SymbolsRules for Safe Operation Read ALL Instructions Blade Coasts After Being Turned OFF Glossary of Terms for Woodworking FreehandUnpacking and Checking Contents Features Miter Lock Handle Spindle Lock ButtonTrigger Lock Positive Stops on Miter TableOptional Accessories Mounting HoleElectrical Connection Trace Holes AT These Locations For Hole PatternAssembly To Install BladeDust Guide Miter TightenDust BAG Table Extensions Stop BlockSee Figures 13, 14, See Figures 13Authorized Service Center AdjustmentsPivot Adjustments Travel Pivot Adjustment Squaring the Miter Table to the Fence See Figures 17Fence Miter Table Blade SlotSquaring the SAW Blade to the Fence See Figures 21Fence Miter Blade Square with FenceOperation ApplicationsCutting with Your Miter SAW CrosscuttingWorkpiece Supports Support Long WorkpiecesLong Workpiece Cutting Warped Material Clamping Wide WorkpiecesRight Wrong Wide BoardMaintenance GeneralLubrication Extension CordsTroubleshooting Problem Cause SolutionOperators Manual 10 in mm Miter Saw Model TS1302 Ryobi TECHNOLOGIES, INC