Ryobi bts20r manual Features, Getting to Know Your SAW

Page 11

FEATURES

Your saw is designed to perform as a versatile, accurate, precision cutting tool that is easy to operate.

It is equipped with the following features for convenience, ease of use, and high-quality performance:

•a combination saw blade

•a bevel indicator to set the exact angle of the blade, with locking lever

•an adjustable sliding table extension

•an adjustable miter gauge

•an adjustable rip fence with scale indicator

•an adjustable riving knife (splitter) and blade guard with anti-kickback pawls

•front and rear guide rails with an easy-to-read scale on front rail

•a dust exhaust that can be adapted to a standard shop vacuum

•blade adjusting handle to set depth of cut

•a sliding outfeed support

•switch with removable switch key to help prevent unauthorized use

•folding leg stand with wheels for ease of transportation These features provide ease of cutting with all types of wood.

WARNING:

Before attempting to use your table saw, familiarize yourself with all operating features and safety requirements.

GETTING TO KNOW YOUR SAW

OUTFEED

SUPPORT

MITER GAUGE

BLADE GUARD

ASSEMBLY

RIVING KNIFE	RIP FENCE
	SAW BLADE
	SLIDING
ANTI-KICKBACK	TABLE EXTENSION
ANTI-KICKBACK
PAWLS

FRONT

RAIL

TABLE TILT

HANDLE

RIP FENCE

LOCKING HANDLE

-	+
BEVEL	SWITCH
HANDLE	BEVEL
BEVEL	LOCKING LEVER
BEVEL
INDICATOR	BLADE
	ADJUSTING
	HANDLE

LEVELING

GRIPFOOT

LEG STAND

Fig. 4

Page 11

Image 11

Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Wrench #2 Phillips Screwdriver Framing Square UnpackingTools Needed Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Speed and WiringBlades Wheel AssemblyAssembling Wheels and HUB Caps Assembling BumpersOpening the LEG Stand Closing the LEG Stand Finger Hole To Install RIP FenceREMOVING/REPLACING the Throat Plate RIP Fence Front RailTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts Push Bevel Locking Locking Lever Left Rotate Blade AdjustingTo Remove the Blade Blade Throatguard PlateInch To CHECK, Replace or Adjust the Blade Guard AssemblyRiving Knife Shims HEX Nuts To SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveOutfeed Support Lower SCALE19 Inch Mark Miter Gauge To USE Outfeed SupportTo USE Sliding Table Extension To Make a Cross CUTTo Make a Straight RIP CUT To Make a Miter CUTMiter Gauge RIP Fence Bevel Locking Lever To Make a Bevel Cross CUTTo Make a Bevel RIP CUT Bevel Locking Lever Pushblock Clamp To Make a Compound Miter CUTTo Make NON-THROUGH Cuts FeatherboardLubrication MaintenanceGeneral Maintenance To Make Dado CutsNuts Clamp Screw RIP Fence Blade Locking Handle Screws To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop BoltProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20R