Ryobi bts20r manual To SET Blade AT 0 or, To Check the Alignment of the RIP Fence to the Blade

Page 31

MAINTENANCE

WARNING:

Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the off () position. Failure to head this warning could result in serious personal injury.

TO SET BLADE AT 0° OR 45°

See Figure 40.

The angle settings of your saw have been set at the factory and, unless damaged in shipping, should not require setting during assembly. After extensive use, it may need to be checked.

￿If the blade is not perfectly vertical (0°), loosen the nuts on the stop bolt inside the cabinet, position the blade, adjust the stop bolt, then retighten nut. See Figure 40, insert.

￿Turn the blade adjusting handle until the bottom of the blade has moved completely to the left side of the slot. Lock the angle by pushing the bevel locking lever.

￿If the blade is not an exact 45°, loosen the nuts on the stop bolt inside the cabinet, position the blade, adjust the stop bolt, then retighten lock nut. See Figure 40, insert.

￿Make a test cut.

TO CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADE

See Figure 41.

-

+

 

 

BEVEL

 

 

LOCKING LEVER

 

BEVEL

 

BEVEL

INDICATOR

NUTS

 

 

HANDLE

 

 

STOP BOLT

 

 

WARNING:

Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the off ( ) position. Failure to head this warning could result in serious personal injury.

￿Raise the locking handle to permit the rip fence to be moved.

￿Place a framing square beside the blade and move the rip fence up to the square. Take the dimension on the rip scale.

￿Move the fence back and turn the framing square 180° to check the other side.

￿If the two dimensions are not the same, loosen the two screws on the fence and align it.

￿Retighten the two screws.

￿Make two or three test cuts on scrap wood. If the cuts are not true, repeat the process.

WARNING:

Before plugging the saw back in to make test cuts, make sure the switch is in the off () position and the blade guard is in place. Failure to do so may result in serious injury.

NUTS

Fig. 40

CLAMP SCREW

RIP FENCE

BLADE

LOCKING

HANDLE

SCREWS

 

RIP

 

FENCE

Fig. 41

 

Page 31

Image 31
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Tools Needed UnpackingWrench #2 Phillips Screwdriver Framing Square Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchBlades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Wheel AssemblyAssembling Wheels and HUB Caps Assembling BumpersOpening the LEG Stand Closing the LEG Stand Finger Hole To Install RIP FenceREMOVING/REPLACING the Throat Plate RIP Fence Front RailTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts Push Bevel Locking Locking Lever Left Rotate Blade AdjustingTo Remove the Blade Blade Throatguard PlateRiving Knife Shims HEX Nuts To CHECK, Replace or Adjust the Blade Guard AssemblyInch To Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveOutfeed Support Lower SCALE19 Inch Mark Miter Gauge To USE Outfeed SupportTo USE Sliding Table Extension To Make a Cross CUTTo Make a Straight RIP CUT To Make a Miter CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTMiter Gauge RIP Fence Bevel Locking Lever Bevel Locking Lever Pushblock Clamp To Make a Compound Miter CUTTo Make NON-THROUGH Cuts FeatherboardLubrication MaintenanceGeneral Maintenance To Make Dado CutsNuts Clamp Screw RIP Fence Blade Locking Handle Screws To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop BoltProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20R