Sears 149.23632 owner manual Safety Rules for JOINTER--PLANER, Assembly, Depth of CUT Hand Knob

Page 5

SAFETY RULES FOR JOINTER--PLANER

Safety is a combination of operator common sense and alertness at all times when the Jointer--Planer is being used. Study these rules and general safety rules before operating and retain them for future use.

1.WEAR EYE PROTECTION.

2.NEVER MAKE JOINTING OR PLANING CUT DEEPER THAN 1/8 INCH -- PER PASS.

3.FEED WORKPIECE AGAINST ROTATION OF CUTTER.

4.KEEP FINGERS AWAY FROM REVOLVING CUTTER --use fixtures when necessary.

5.NEVER PERFORM JOINTING OR PLANING OPERATION WITH CUTTER HEAD GUARD REMOVED.

6.NEVER FORCE CUTTING ACTION. Stalling or partial stalling of motor can cause major damage. Allow motor to reach full speed before cutting.

7.NEVER - Attempt to perform an abnormal or little used operation without study and the use of adequate hold down /push blocks, jigs, fixtures, stops, etc.

8.NEVER - Attempt to cut small pieces.

9.ALWAYS - Use hold down/push blocks for jointing material narrower than 3 inches, or planing material thinner than 3 inches.

10.ALWAYS- Keep cutter sharp.

11.NEVER- Use in an explosive atmosphere. Normal sparking of motor may ignite fumes.

12.OUTDOOR EXTENSION CORD USE - When tool is used outdoors, use only extension cords suitable for use outdoors. Outdoor approved cords are marked with the sL'ffix W-A, for example- SJTW-A or SJOW-A.

13.ALWAYS use identical replacement parts when servicing.

14.This tool is intended for RESIDENTIAL USE ONLY.

WARNING: DO NOT ALLOW FAMILIARITY (GAINED FROM

FREQUENT USE OF YOUR JOINTER--PLANER) TO BECOME

COMMONPLACE. ALWAYS REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY.

WARNING: DO NOT AT ANY TIME LET BRAKE FLUIDS, GASOLINE, PENETRATING OILS, ETC.

,_

COME

IN CONTACT

WITH PLASTIC PARTS. THEY CONTAIN CHEMICALS THAT CAN DAMAGE

 

AND/OR

DESTROY

PLASTICS.

ASSEMBLY

DEPTH OF CUT HAND KNOB

1.Find one 3/8 lockwasher and the depth of cut hand knob from the parts bag.

2.Turn the nut on the height adjustment screw until five full threads extend beyond the nut.

3.Place Iockwasher on height adjustment screw and thread hand knob onto screw.

4.Back nut up against hub of hand knob. Tighten with 14ram or 9/16 wrench while holding hand knob.

CHIP DEFLECTOR

1.Loosen the screw in the center of vacuum port of chip discharge.

2.Install slot of chip deflector between the chip discharge and the flat washer and retighten.

,_CAUTION:THE CHIP DEFLECTOR MUST BE IN PLACE

FOR SAFE OPERATION. FAILURE TO INSTALL THE CHIP

DEFLECTOR MAY RESULT IN PERSONAL INJURY.

3/8 HEX NUT

t

DEPTH OF CUT

HAND KNOB

LOOSEN AND

RETIGHTEN

T H I S SC R E W _

_.

DEFLECTOR

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Serial Or Code Number ModelnoFull ONE-YEAR Warranty on £RRFTSMRN, Jointer -- Planer General Safety Rules for Power ToolsTable of Contents Tools Required Unpacking and Checking ContentsAssembly Safety Rules for JOINTER--PLANERDepth of CUT Hand Knob Chip DeflectorFence Checking Cutter BladesBlade Head Clamp Screw Chip DISCHARGE/VACUUMFlathead Fence ExtensionCountersunk Screws -- .I FencejControls and Adjustments Installing the JOINTER--PLANERFence Cutterguard ON-OFF Switch Depth of CUT Hand KnobsON-OFF Switch Fence AdjustmentTo Check Depth of CUT Outfeed Cutter GuardFeeding the Work Piece Contact with the Cutter Causing Serious InjuryBasic JOINTER---PLANER Operation Beveling and Chamfering Using Hold DOWN/PUSH BlocksIf the Hold Slip While FEEDING, Clean Rubber Surface Using a WET--DRY VAC MaintenanceTiming Belt Replacement Cutter Guard Return SpringGeneral Maintenance Blade Replacement and AdjustmentBlade Wood Cutterblock Head CLAMP.ADE Icals That can Damage AND/OR Destroy PlasticsRepair Parts =, R 51/8-INCH JOINTER-PLANER Trouble ShootingModel Number Name Item 5-118 Inch JOINTER--PLANER
Top Page Image Contents