Grizzly G5771 owner manual Service, Troubleshooting

Page 26

SECTION 6: SERVICE

Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel- ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663.

Troubleshooting

Operations

Symptom				Possible Cause		Possible Solution

Slip	roll	creates		1.	Rollers are not parallel.	1.	Adjust rear roller adjustment knobs as necessary to
cones	when trying						be sure the rear roller and upper roller are parallel.
to create cylinders.

A noticeable crease				1.	Excessive pressure applied in one spot.	1.	Reduce the radius and perform the bend in several
is formed		in	the				passes.
workpiece.

Crank does not turn				1.	Gearbox end of upper roller is not secure.	1.	Re-center the bushing and secure the hex bolt and
upper	and	lower					jam nut (Step 5 on Page 20).
rollers.				2.	Gears are damaged.	2.	Check/Replace gears.
				2.	Gears are damaged.	2.	Check/Replace gears.

Slip roll does			not	1.	Machine capacities exceeded.	1.	Use materials within the capacity of the slip roll.
bend material.				2.	Rear roller not engaged.	2.	Check/Adjust rear roller.

-24-	G5771 50" Slip Roll 16 Gauge

Image 26

Contents Model G5771 Slip Roll 16 Gauge Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Identification Identification List Figures 1Machine Data Sheet !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety for Slip Rolls Items Needed for Setup SetupSetup Safety UnpackingInventory Box 1 Figure QtyHardware Recognition Chart Clean Up Site ConsiderationsAssemblyMounting To assemble your machineOperation Safety Basic Controls OperationsFlat Rolling Upper roller bushingCreating Bends Raising lower rollerProcessing the workpiece G5771 50 Slip Roll 16 Gauge Creating Cylinders To create a cylinderFigures 25 Removing Workpiece on Bending WireTo use the wire grooves Removing Workpiece To remove cylindrical workpiecesG5618-Deburring Tool with two Blades AccessoriesH6073-Deluxe Power Snip G5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz SprayG8781-41⁄2 Suction Cup G4956-Super NibblerH5958-Sheet Metal Pliers H6131-Heavy-Duty Hand RiveterSchedule MaintenanceCleaning Unpainted Cast IronService TroubleshootingParts BreakdownParts List Description22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%