Hobart Welding Products 625 manual Definitions, I1max, I1eff

Page 13

.A complete Parts List is available at www.HobartWelders.com

SECTION 3 − DEFINITIONS

3-1. Symbols And Definitions For Nameplate And Serial Number/Rating Label

Amperes

Plasma Arc Cutting

Adjust Air/Gas

Low Air Pressure

(PAC)

Pressure

Light

Volts

Increase

No − Do Not Do

Temperature

This

Protective Earth

Single Phase

Constant Current

Voltage Input

(Ground)

Off

Percent

Direct Current

Rated No Load

Primary Voltage

Conventional Load

Line Connection

Voltage (Average)

Voltage

I1max

Single Phase

Rated Maximum

Rated Welding

Static Frequency

Supply Current

Current

Duty Cycle

Converter-

Transformer-

Rectifier

Degree Of

Loose Shield Cup

Input

Hertz

Protection

I1eff

Suitable for Some

Power Rating,

Maximum Effective

power factor

Hazardous

Product Of Voltage

Supply Current

Locations

And Current (KVA)

OM-926 Page 9

Image 13

Contents Processes OM-926Description File Plasma CuttersFrom Hobart to You Table of Contents Page Marks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosionFlying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearingCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulier LE Bruit peut endommager l’ouïe Risque de blessure en cas LES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresDES Organes Mobiles peuvent provoquer des blessures DES Pieces Chaudes peuvent pro- voquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OUInformation sur les champs électromagnétiques Principales normes de sécuritéLE Coupage Ã L’ARC peut causer des interférence Consignes relatives aux stimulateurs cardiaquesI1max − DefinitionsI1eff Specifications − InstallationSpecifications For Torch Torch Dimensions And WeightDimensions And Weight Unit Dimensions, Weight, And MovementMovement Do not move or operate unit where it could tip 90-120 psi Connecting Work Clamp and Gas/Air SupplyRear of Unit 50/60 Hz Single Phase Electrical Service GuideTime-Delay Extension Cord DataDo not move or operate unit where it could tip = GND/PE Selecting a Location And Connecting Input PowerAlways connect green or Prong Not UsedTerminal, never to a load TerminalsSetting Gas/Air Pressure Installing Alternative PlugSetting Gas/Air Pressure − Operation Pressure Gauge Pressure Adjustment KnobControls Cutting SpeedPilot arc starts immediately when trigger is pressed Trigger Safety LockWhen doing extended non-shielded Plasma Cutting System PracticesArea as possible Sequence Of Cutting OperationHold torch at approximately Angle to workpiece Sequence Of Gouging OperationCutting Sequence Of Piercing OperationRoutine Maintenance − Maintenance & TroubleshootingShield Cup Checking Torch Shield Cup Shutdown SystemChecking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch partsCheck torch consumables Troubleshooting Power SourceIs Temp Status Light On? Is Pressure StatusTroubleshooting Torch Circuit Diagram − Electrical DiagramRecommended Spare Parts − Parts ListRecommended Spare Parts 195 110 ICE-40C 25ft Torch 195 111 ICE-40C 50ft Torch See -1for additional Consumable partsWork like a Pro Support ServiceAssistance Hobart Welding Products Contact your Distributor for