Hobart Welding Products 625 manual Contact your Distributor for, Hobart Welding Products

Page 36

Owner’s Record

Please complete and retain with your personal records.

Model Name	Serial/Style Number
Purchase Date	(Date which equipment was delivered to original customer.)

Distributor

Address

City

State	Zip

Resources Available

Always provide Model Name and Serial/Style Number.

Protect Your Investment!

Register your product at:

HobartWelders.com

To locate a Distributor, retail or service location:

Call 1-877-Hobart1 or visit our website at www.HobartWelders.com

For technical assistance:

Call 1-800-332-3281

Contact your Distributor for:

Welding Supplies and Consumables

Options and Accessories

Personal Safety Equipment

Service and Repair

Replacement Parts

Training (Schools, Videos, Books)

Technical Manuals (Servicing Information and Parts)

Circuit Diagrams

Welding Process Handbooks

Hobart Welding Products

An Illinois Tool Works Company

600 West Main Street

Troy, OH 45373 USA

For Technical Assistance:

Call1-800-332-3281

For Literature Or Nearest Dealer:

Call 1-877-Hobart1

Contact the Delivering Carrier to:	File a claim for loss or damage during
	shipment.
	For assistance in filing or settling claims, contact
	your distributor and/or equipment manufacturer’s
	Transportation Department.
PRINTED IN USA	♥ 2007 Hobart Welding Products. 2007−01

Image 36

Contents OM-926 ProcessesDescription File Plasma CuttersFrom Hobart to You Table of Contents Page Symbol Usage Marks a special safety messagePlasma Arc Cutting Hazards Cutting can cause fire or explosionExploding Parts can injure Flying Sparks can cause injuryARC Rays can burn eyes and skin Noise can damage hearingCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers Signification des symboles LE Coupage présente un risque de feu ou d’explosionUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulierRisque de blessure en cas LE Bruit peut endommager l’ouïeLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresDES Pieces Chaudes peuvent pro- voquer des brûlures graves DES Organes Mobiles peuvent provoquer des blessuresLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OUPrincipales normes de sécurité Information sur les champs électromagnétiquesLE Coupage Ã L’ARC peut causer des interférence Consignes relatives aux stimulateurs cardiaques− Definitions I1maxI1eff − Installation SpecificationsSpecifications For Torch Torch Dimensions And WeightUnit Dimensions, Weight, And Movement Dimensions And WeightMovement Do not move or operate unit where it could tip Connecting Work Clamp and Gas/Air Supply 90-120 psiRear of Unit Electrical Service Guide 50/60 Hz Single PhaseTime-Delay Extension Cord DataSelecting a Location And Connecting Input Power Do not move or operate unit where it could tip = GND/PEProng Not Used Always connect green orTerminal, never to a load TerminalsInstalling Alternative Plug Setting Gas/Air PressureSetting Gas/Air Pressure Pressure Gauge Pressure Adjustment Knob − OperationControls Cutting SpeedTrigger Safety Lock Pilot arc starts immediately when trigger is pressedWhen doing extended non-shielded Plasma Cutting System PracticesSequence Of Cutting Operation Area as possibleSequence Of Gouging Operation Hold torch at approximately Angle to workpieceSequence Of Piercing Operation Cutting− Maintenance & Troubleshooting Routine MaintenanceChecking Torch Shield Cup Shutdown System Shield CupTurn Off power source before checking torch parts Checking/Replacing Retaining Cup, Tip, And ElectrodeTroubleshooting Power Source Check torch consumablesIs Temp Status Light On? Is Pressure StatusTroubleshooting Torch − Electrical Diagram Circuit Diagram− Parts List Recommended Spare PartsRecommended Spare Parts See -1for additional Consumable parts 195 110 ICE-40C 25ft Torch 195 111 ICE-40C 50ft TorchWork like a Pro Service SupportAssistance Contact your Distributor for Hobart Welding Products