Grizzly G0671, G0673, G0672 owner manual Collector mounted to impeller Housing

Page 24

4.Attach the four casters to the legs by thread- ing them into the bottom of the legs, as shown in Figure 15.

Caster

Leg

m)

Figure 15. Attaching casters.

5.With assistance, turn the entire assembly over so that the casters rest on the floor.

6.Use eight 5⁄16"-18 x 1" hex bolts, (16) 5⁄16" flat washers, and eight 5⁄16"-18 hex nuts to attach each collector to the impeller housing with a rubber gasket between the components, as shown in Figure 16.

5⁄16" Flat Washers

Impeller

Collector

housing

 

 

5⁄16"-18

 

Hex Nut

5⁄16"-18 x 1"

 

Hex Bolt

 

Rubber Gasket

Figure 16. Collector mounted to impeller

housing.

Note: The Model G0673 is a three-phase machine. If it is wired out of phase, the machine may not function properly. Proceed to Test Run on Page 25 to determine if your machine is wired in phase, then proceed to Step 7.

The Models G0671 and G0672 are single phase and cannot be wired out of phase. For these models, continue below.

7.Attach the inlet to the top of the impeller housing with the #10-24 x 3/8" Phillips head screw, as shown in Figure 17.

Phillips

Head Screw

Figure 17. Inlet mounted on impeller housing.

-22-

G0671/G0672/G0673 Dust Collector

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Dust Collector Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Machine Data Sheet Main Specifications Operational Information Performance Curve Model G0672 HP Dust Collector Main Specifications Operational Information CFM Model G0673 HP Industrial Dust Collector Main Specifications Operational Information Model G0673 HP Dust Collector  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2  53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety for Dust Collectors Circuit Requirements OperationSetup Setup SafetyItems Needed for Setup UnpackingContents Figures 7 Qty Fasteners where used not shown QtyG0671/G0672 Inventory Contents Figures Qty G0673 InventoryHardware Recognition Chart Assembly Placement LocationSite Considerations Floor LoadCollector mounted to impeller Housing Upper filter bag secured to collector Page Test Run Designing System General Duct MaterialMetal Duct Flexible Duct Plastic DuctSystem Design Decide Who Will DesignSketch Your Shop Layout Sketch a Basic Duct LayoutDetermine Required CFM of Each Machine Machine ApproximateMachine Determining Main Line Duct Size Determining Branch Line Duct SizeMultiple Dust Ports Two Machines on Same Branch LineCalculating Duct Resistance Duct Approximate DiaLoss Per Foot Additional Factors Static Pressure LossPerformance Curve System Grounding Operation Safety Basic Controls OperationsGeneral Accessories Metal Duct Starter KitMetal Elbows Reducers & AdaptersH2443-9 1⁄2 x 6 Universal Adapter Maintenance Lubrication Bag CleaningSchedule Daily CheckService TroubleshootingMotor & Electrical Symptom Possible Cause Dust Collection OperationWiring Electrical Safety InstructionsG0671/G0672 Wiring Diagram Color KEYG0673 Wiring Diagram See FigureG0673 220V switch G0673 Electrical ComponentsParts G0671 Parts BreakdownG0671 Parts List DescriptionG0672 Parts Breakdown G0672 Parts List G0673 Parts Breakdown G0673 Parts List Label Placement G0671 G0672 G067322!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents