Jet Tools DC-1100MK, DC-1100CK, DC-1100BK operating instructions

Page 4

1.Read and understand the entire owner's manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This dust collector is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a dust collector, do not use until proper training and knowledge have been obtained.

5.Do not use this dust collector for other than its intended use. If used for other purposes, Walter Meier (Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this dust collector. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this dust collector, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power supply.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17.Provide for adequate space surrounding work area and non-glare, overhead lighting.

18.Keep the floor around the machine clean and free of scrap material, oil and grease.

19.Keep visitors a safe distance from the work area. Keep children away.

4

Image 4
Contents Dust Collector Warranty and Service More InformationTable of Contents Page Introduction Specifications Base Machine All ModelsUnpacking Shipping ContentBase Unit Canister Filter Kit Micron Bag Filter KitBase Unit Assembly Motor and Fan AssemblyConnector Housing BaseImpeller housing D with two clamps HoseFilter Bag Kit Assembly Filter Bag InstallationCollector Bag Installation 30 Micron Kit Collector Bag Installation 5 Micron KitCanister Filter Canister Kit AssemblyCollector Bag Dust Collector RF Remote Power Control Optional Electrical ConnectionsTurning the Machine On & Off All ModelsInstalling the DC-RC Remote Power Changing Operating FrequencyMaintenance Parts Breakdown DC-1100 Dust Collectors Parts List DC-1100 Dust Collectors Ordering Replacement Parts Index No Description Size QtyCanister Filter Kit 708639B Index No. Part No Description Size QtyMicron Filter Bag Kit 708636F Micron Filter Bag Kit 708636MF Wiring Diagram DC-1100 Dust Collectors Page Page Walter Meier Manufacturing Inc
Related manuals
Manual 20 pages 2.04 Kb