MartinLogan MAC 500/E user manual Fault c o l o r f i l t e r p o s i t i o n s

Page 20

D e f a u l t c o l o r f i l t e r p o s i t i o n s

Color wheel 1

Wheel as seen from front, in open position.

1

2

3

4

5

6

7

8

9

Blue 111

Red 301

Magenta 507 Green 202

Yellow 604

Purple 502

Blue 101

Pink 312

Cyan 401

62327015

62327021

62327023

62327018

62327019

62327025

62327016

62327022

62327017

C h a n g i n g c o l o r f i l t e r s

W A R N I N G !

Disconnect the fixture from AC power before removing any cover.

1.Remove the top head cover as described under “Accessing parts” on page 21.

2.Manually turn the color wheel until the desired filter is accessible.

3.Using a soft cloth or gloves, gently tilt the outside edge of the filter towards the front lens and remove.

4.To place a filter in the wheel, insert the plastic holder between the spring clip - with the protrud- ing tab facing the lamp - until it snaps into place.

20

MAC 500/E User Manual

Page 19 Page 21
Image 20
Page 19 Page 21
Contents
MAC 500/E Page Introduction C t i o n T R O D U C T I O NC 5 0 0 / E s a f e t y i n f o r m a t i o n P a c k i n g Install i n g o r c h a n g i n g t h e l a m pT U P Install a p l u g o n t h e p o w e r c o r d Wire Pin Marking Screw USW e r i n g t h e f i x t u r e G g i n gN n e c t i n g f i x t u r e s N n e c t i n g t h e s e r i a l l i n kP s f o r b u i l d i n g a s e r i a l l i n k Page E R a T I O N R t i n R S 4 8 5 c o n t r o lX 5 1 2 c o n t r o l Tr a c k i n g c o n t r o lN t r o l l a b l e e f f e c t s T a t i n g g o b o s I sT a t i n g p r i s m / v a r i a b l e f r o s t M m e r / s h u t t e rN T R O L P a N E L N u n a v i g a t i o nR s o n a l i t y s e t t i n g s D r e s s a n d p r o t o c o l s e l e c t i o n A d o u t sN u a l c o n t r o l A n d a l o n e s e q u e n c e s S e t d e Fault o f f s e t s SPEC/dFOF I l i t i e s L i b r a t i o n C a L L o a d m o d e UPLdB o Specification s B O S a N D C O L O R F I L T E R SB o o r i e n t a t i o n a n d p o s i t i o n s A s s g o b o sO s e r o t a t i n g g o b o f i Fault g o b o l a y o u tT a l a n d i m a g e g o b o s A n g i n g r o t a t i n g g o b o s A n g i n g s t a t i c g o b o sT h o u t t o o l s T h n e e d l e n o s e p l i e r sFault c o l o r f i l t e r p o s i t i o n s A n g i n g c o l o r f i l t e r sI N T E N a N C E a N D B a S I C S E R V I C E C e s s i n g p a r t sM o v i n g t h e p r i n t e d c i r c u i t b o a r d E n i n g t h e h e a dC 5 0 0 w i t h m a g n e t i c b a l l a s t P l a c i n g f u s e sA n g i n g t h e X L R p i n o u t O t m o d e u p l o a d C 5 0 0 E w i t h e l e c t r o n i c b a l l a s tR m a l u p l o a d A n g i n g l e n s e s P l a c i n g t h e l a m pT i m i z i n g l a m p a l i g n m e n t I n t e n a n c e s c h e d u l eE a n i n g B r i c a t i o nT i c a l c o m p o n e n t s N sP E N D I C E S X p r o t o c o lDMX Channel Start code = Percent FunctionAlternate Functions Enable on channel Value Percent FunctionFixed Gobos Value Combined Rotating Prism and Gobo MacrosS s a g e s Display readout Appears if What to doProblem Probable causes Remedy Tr o u b l e s h o o t i n gR c u i t b o a r d l a y o u t Specification s C e s s o r i e s MAC 500 DMX Protocol
Top Page Image Contents