Powermatic 60B operating instructions

Page 5

20.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

21.Keep visitors a safe distance from the work area. Keep children away.

22.Make your workshop child proof with padlocks, master switches or by removing starter keys.

23.Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury.

24.Maintain a balanced stance at all times so that you do not fall or lean against the knives or other moving parts. Do not overreach or use excessive force to perform any machine operation.

25.Use recommended accessories; improper accessories may be hazardous.

26.Maintain tools with care. Keep knives sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.

27.Turn off the machine and disconnect from power before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands.

28.Do not stand on the machine. Serious injury could occur if the machine tips over.

29.Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

30.When working a piece of wood on the jointer, follow the 3-inch radius rule: The hands must never be closer than 3 inches to the cutterhead. See Figure 1.

31.Always use a hold-down or push block when surfacing stock less than 12 inches long, or 3 inches wide, or 3 inches thick.

32.Do not perform jointing operations on material shorter than 8 inches in length, narrower than 3/4 inches, or less than 1/4 inch thick.

33.Do not make cuts deeper than 1/8 inch to avoid overloading the machine and to minimize chance of kickback.

34.Never apply pressure to stock directly over the cutterhead. This may result in the stock tipping into the cutterhead along with the operator’s fingers. Position hands away from extreme ends of stock, and push through with a smooth, even motion. Never back workpiece toward the infeed table.

35.“Pull-out” and the danger of kicked back stock can occur when the work piece has knots, holes, or foreign materials such as nails. It can also occur when the stock is fed against the grain on the jointer. The grain must run in the same direction you are cutting. Before attempting to joint or plane, each work piece must be carefully examined for stock condition and grain orientation.

NOTE: At certain times it may be necessary to plane against the grain when working with a swirl grain wood or burl. With this type of work the operator must use a lesser depth of cut and a slow rate of feed.

5

Image 5
Contents Part No. M-0460282 Inch JointerMore Information Warranty and ServiceTable of Contents Page Page Page Features of the 60B Jointer SpecificationsCrate #1 contents Installation and AssemblyCrate #2 contents Tools required for assemblyMounting Drive Belt Aligning PulleysMounting Pulley Guard Mounting Dust ChuteGrounding Instructions Electrical ConnectionsExtension Cords Converting from 230 Volt to 460 Volt Three Phase OnlyCutter Guard AdjustmentsRemoving Guard Mounting GuardInstalling Knives Leveling Tables Rapid Adjust Adjusting Depth of CutFine Adjust If table will still not line upSpring Cutting Setting Outfeed TableExamples of incorrect settings Degree stop Fence MovementFence Stops Jointing Short or Thin Work Basic Jointer OperationDegree forward stop Degree back stopDirection of Grain Hand PlacementSurfacing Jointing Warped SurfacesSkewing Shear Cutting Edge JointingBeveling Rabbeting Taper CutsCutterhead Repairs MaintenanceSharpening Knives Table Removal Probable Cause Remedy Troubleshooting Operating ProblemsTrouble Troubleshooting Mechanical and Electrical Problems Trouble Probable Cause Remedy Optional AccessoriesReplacement Parts Index No. Part No Description Size Qty Parts List Base Assembly6296166 Base Assembly Parts List Fence Assembly Fence Assembly Parts List Cutterhead Assembly Parts List Stand Assembly 6823013 Stand Assembly Electrical Connections 230 Volt, Single Phase Electrical Connections 230 Volt, 3 Phase Electrical Connections 460 Volt, Three Phase Checklist for Model 60B Jointer Preventive MaintenanceWMH Tool Group