Ryobi A25RT02 manual Applications, Performing a Routing Operation

Page 17

OPERATION

WARNING:

Do not allow familiarity with products to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

APPLICATIONS

You may use this product for the purposes listed below:

�Table mounted dado and mortise operations in wood and wood composition materials

Fence guided edging operations for cabinetry and picture framing on wood and wood composition materials

Piloted cutter operations using the starting pin for edging patterned surfaces on wood and wood composition materials

WARNING:

The direction of feed for the workpiece is always against the sharp edges of the cutter and therefore into the rota- tion of the cutter. Failure to heed this warning can result in serious personal injury.

WARNING:

When operating the router with the router table, the router must only be plugged into and controlled by the router table switched outlet. To reduce the risk of serious personal injury, never connect the table mounted router into another power source.

WARNING:

The router or router table should never be connected to a power supply when you are assembling parts, making adjustments, installing or removing cutters, cleaning, or when not in use. Disconnecting the router and router table will prevent accidental starting that could cause serious personal injury.

PERFORMING A ROUTING OPERATION

Observe the following rules when using the router.

Read the entire operator’s manual for the router and router table.

Plug the router table power cord into a power source.

Always control the power to the router with the router table switch whenever the router is mounted on the table.

Always plug the router into either of the router table switched outlets. Never plug a router table mounted router into another power source.

Position the infeed and outfeed fence so they are close to the maximum diameter of the cutter, but not touching the cutter.

NOTE: The workpiece must always be tight against the fence, unless you are using a ball-bearing piloted cutter.

Adjust the infeed fence to support the uncut workpiece and adjust the outfeed fence to support the workpiece after the cut. The “0” location on the fence scale denotes the center of the throat opening of the table.

Reconfirm that all router adjustments are securely locked before connecting the router table to a power source.

Feed the workpiece from right to left with the cutter in line with the fence opening.

Make sure the router table switch is off when not in use. Remove the switch key to ensure the router table is off.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyRead ALL Instructions General Safety Rules Always USE the Articulating Router Cutter BIT Guard Specific Safety Rules do not USE Awkward Hand Positions  Always Feed Workpiece Against Rotation of CutterName DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Speed and WiringExtension Cords Electrical ConnectionFeatures Switch Assembly Reset ButtonStarting PIN Throat PlatesPacking List AssemblyUnpacking Assembling the Router Table Attaching the Switch BOXAttaching the Under Table Guards Attaching the Table LegsInstalling the ROUTER/INSERT Plate Assembly PRE-DRILLING Holes for Through Table Depth AdjustmentAttaching the Router to the Table Attaching the Router to the Insert PlateKM12VC HEX KEY Insert Plateadjusting Straight Screws Edge Attaching the Fence AssemblyMaking Insert Plate Level Inserting and Removing Throat PlatesInserting the Starting PIN Installing the Miter GaugeAttaching the Featherboard Mounting the Router Table to a Work Bench Attaching the Vacuum HoseClamping the Router Table to a Work Bench Performing a Routing Operation OperationApplications Adjusting the Miter Gauge Adjusting Depth of CUTINSERTING/REMOVING Cutters Positioning the FenceGeneral Maintenance MaintenanceParts and Service

A25RT02 specifications

The Ryobi A25RT02 is a versatile and robust tool designed for both home improvement enthusiasts and professional contractors. This innovative product features a powerful motor that enhances its performance across a range of applications, making it an essential addition to any toolbox.

One of the standout features of the A25RT02 is its lightweight and ergonomic design. Weighing in at just a few pounds, this tool is easy to handle and reduces user fatigue during prolonged use. The rubber overmolded grip provides comfort and stability, allowing for precise control whether you're working on delicate projects or heavy-duty tasks.

The A25RT02 is equipped with advanced technology that enables quick adjustments and versatility. Its adjustable cutting depth and width make it suitable for various materials, ensuring that users can achieve the desired finish with ease. The tool also features a variable speed control that allows for customization based on the application, providing better results whether you're cutting, sanding, or shaping.

Another remarkable characteristic of the A25RT02 is its compatibility with Ryobi's extensive line of ONE+ batteries, which offers greater convenience and portability. This means users can easily switch between different Ryobi tools without the hassle of changing batteries or being tethered to a power outlet. The battery life is impressive, allowing users to complete tasks without frequent interruptions for recharging.

Safety is a key consideration in the design of the A25RT02. It comes with built-in safety features such as a blade guard and a safety switch to prevent accidental activation. These features contribute to a safer working environment, particularly when working on complex or intricate projects.

Durability is another hallmark of the Ryobi A25RT02. Constructed with high-grade materials, this tool is built to withstand the rigors of daily use, ensuring longevity and reliability. The easy-to-replace parts further extend its usability, making repairs straightforward without the need for specialized tools.

In summary, the Ryobi A25RT02 is a cutting-edge tool that combines power, versatility, and safety in a user-friendly package. Its lightweight design, compatibility with the Ryobi ONE+ battery system, advanced speed settings, and robust safety features make it an ideal choice for anyone looking to enhance their craftsmanship. Whether you're a hobbyist or a professional, the A25RT02 is sure to meet your creative and practical needs.
Top Page Image Contents