Powermatic PM15 operating instructions

Page 4

1.Read and understand the entire owner’s manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This planer-molder is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a planer-molder, do not use until proper training and knowledge have been obtained.

5.Do not use this planer-molder for other than its intended use. If used for other purposes, Walter Meier (Manufacturing) Inc. disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this machine. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this planer-molder, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power supply.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16.Make sure the casters are locked before operating the planer-molder.

17.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

18.Provide for adequate space surrounding work area and non-glare, overhead lighting.

19.Keep the floor around the machine clean and free of scrap material, oil and grease.

20.Keep visitors a safe distance from the work area. Keep children away.

4

Image 4
Contents Walter Meier Manufacturing Inc Part No. M-0460264Warranty and Service More InformationTable of Contents Page Page Introduction Specifications Turn = 1/16Contents of the Shipping Container Installation and AssemblyUnpacking Installing Handwheel Installing Dust ChuteElectrical Connections Adjustments Planer Knife ReplacementExtension Cords Belt TensionSharpening Knives Depth of Cut Feed RatePlaner’s Feed System Anti-Kickback FingersInfeed Roller Chipbreaker Leveling Cutterhead with Bed Interlock Switch OperationCaster Lock Kinds of WarpPlaning to Desired Thickness Thickness Planing StepsIntroduction to Molding Planing for FinishPattern Knives Optional Bedboard and GuideInstalling Single Pattern Knives Homemade BedboardHomemade Featherboard Homemade Guide Set-Up for Edge MoldingInstalling Three-Knife Set Pattern Knife ClearanceInstalling Bedboard Face Molding with pattern knivesBedboard must be installed on the planer when edge planing Edge Molding with pattern knivesEdge Planing Common Molding ApplicationsRabbet Maintenance LubricationTrouble Probable Cause RemedyOne cause of overload trips which is Trouble Probable Cause Remedy Troubleshooting Operating Problems Replacement Parts Parts List Base Assembly Index No Description Size QtyBase Assembly Parts List Gearbox Assembly Index No. Part No Description Size QtyGearbox Assembly Parts List Stand Assembly Stand Assembly Parts List Cutterhead, Hood and Table Assembly PM15-HP Cutterhead, Hood and Table Assembly Electrical Connections Page New Sanford Road LaVergne, Tennessee Phone
Related manuals
Manual 6 pages 40.8 Kb