Powermatic 201HH operating instructions Outfeed Roller, Table Rollers

Page 14

Outfeed Roller

The outfeed roller is of smooth, one-piece construction to help avoid marring the finished surface of the material being cut. It is spring tensioned, and its function is to continue to feed the material through the machine after it leaves the infeed roller. The correct free position setting is 1/32" (0.8mm) below the arc of the cutterhead knives.

Use a gauge, such as a bed and feed roll gauge or wood gauge block (see Figure 13) to check the outfeed roller in the same manner as for the infeed roller. Adjust as necessary using the screws (E, Figure 15). When finished adjusting, tighten the hex nuts on the screws.

Table Rollers

The Planer has two table rollers which help reduce friction of the stock on the table as it feeds through the machine. It is not possible to give exact height setting of the table rollers because each type of wood behaves differently. As a general rule, however, the table rollers should be set high when planing rough stock, and set low for finish cuts.

The planer is equipped with a quick set table roller adjustment. With a single lever, you can raise the rolls from their finishing board height to a roughing board height. The range is 0.00 to 0.05”.

To adjust the height of the table rollers, loosen the handle (A, Figure 16) and move the quick- set lever (B, Figure 16) until the indicator is at the desired setting on the scale. Re-tighten the handle (A, Figure 16) to lock the setting.

NOTE: The handle (A) is adjustable. To re- position it, simply lift out on the handle, rotate it on the pin and release, making sure it seats itself properly on the pin.

The table rollers are adjusted at the factory. If they should need further or “fine” adjustment:

1.Disconnect machine from power source.

2.Loosen lock handle and position the quick- set lever (Figure 16) to zero.

3.Use a dial gauge (not provided) to find the distance from table top to the apex of the table roller. Zero the gauge at this position.

4.Place the gauge over the extreme right side of the table roller and find the high point of the table roller arc. The gauge should still read zero.

Figure 15 (repeated)

Figure 16

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Inch Planer Warranty and Service More InformationTable of Contents Page Page Introduction Specifications 1791269Installation ReceivingInstalling Dust Hood Grounding InstructionsInspection AdjustmentsFeed Rate Adjustment Depth of CutKnife Installation and Adjustment Straight Cutterhead only Opening HoodReplacing or Rotating Knife Inserts Helical Cutterhead only Model 201HH onlyInfeed Roller Planer’s Feed SystemAnti-Kickback Fingers Chipbreaker Pressure BarOutfeed Roller Table RollersTable Adjustments Test Cutting Troubleshooting Operating ControlsSnipe Maintenance LubricationTroubleshooting Planer Operating Problems Troubleshooting Mechanical and Electrical Problems Replacement Parts Parts List Base Assembly Index No. Part No Description Size Qty6012067 Gearbox Assembly Parts List Gearbox Assembly Column Assembly Parts List Column Assembly Table Assembly Parts List Table Assembly Parts List Top Cover Assembly Cutterhead Assembly Parts List Cutterhead Assembly 6012180 Electrical Connections 1 Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt

201HH specifications

The Powermatic 201HH is a highly regarded 8-inch jointer, renowned for its robust construction, precision, and advanced technology. This machine is particularly well-suited for both professional woodworkers and serious hobbyists who demand the best performance from their tools.

One of the standout features of the Powermatic 201HH is the Helical Cutterhead. This technology distinguishes it from standard jointers featuring straight knives. The helical design incorporates numerous small, square inserts that can be rotated or replaced when worn, significantly extending the overall life of the cutterhead. The helical arrangement reduces noise during operation and provides a much smoother finish on the workpiece, minimizing the need for additional sanding.

Adjustability is another area where the Powermatic 201HH excels. It boasts an easy-to-use tables adjustment mechanism that allows users to fine-tune the infeed and outfeed tables for precise jointing. This feature is essential to ensure a perfectly flat and even surface on all types of wood. The large tables, measuring 74 inches in length, provide ample support for larger workpieces, making it easier to manage and maneuver materials during operation.

The 201HH also comes equipped with a powerful 3 HP motor that drives the machine with reliability and performance. This motor is a key component in delivering consistent power and maintaining speed even under heavier workloads. Coupled with a strong base and solid construction, the jointer maintains stability during operation, which contributes to both safety and precision.

Added convenience comes in the form of an integrated dust collection port, which facilitates cleaner operation by effectively managing sawdust and shavings. This reduces cleanup time and creates a more pleasant working environment.

Moreover, the design of the Powermatic 201HH incorporates safety features, including a push block that assists in guiding stock through the machine, minimizing the risk of injury. The solid build quality and attention to detail in the engineering provide confidence to users that they are working with a reliable tool that will stand the test of time.

In summary, the Powermatic 201HH offers an impressive array of features including a helical cutterhead, extensive adjustability, a powerful motor, efficient dust collection, and strong safety measures. These characteristics make it a top choice for anyone looking to achieve exceptional results in their woodworking projects.
Top Page Image Contents