Powermatic 201HH operating instructions Receiving, Installation

Page 7

Receiving

Open shipping crate and check for shipping damage. Report any damage immediately to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions.

Contents of crate: 1 planer

1 dust chute w/ fasteners

4screws w/ hex nuts (for leveling feet)

4 leveling feet

1 knife-setting gauge (201 only)

2star point screwdrivers (201HH only)

1 set of 10 knife inserts (201HH only)

10 knife insert screws (201HH only)

1 6mm hex wrench

1 8mm hex wrench

1 10mm hex wrench

1 12mm & 14mm wrench

1 22mm & 24mm wrench

1 Operating Instructions and Parts Manual

1 Warranty Card

Installation

Remove the screws holding the base of the machine to the skid. Use the lifting eyes on front and back of the planer for hoisting it off the skid. See Figure 1. Make sure the hex nuts are tightened before lifting. The lifting eyes can be removed once the planer is situated.

Place the planer on a solid foundation, preferably a concrete floor. The four leveling feet should be placed beneath the corners, and the screws and hex nuts used for leveling adjustments. See Figure 2. Alternatively, you can secure the machine to the floor by using lag screws through the holes in the base.

The machine area should be clean, dry, well ventilated, and well lighted. Since planers can create noise problems, the site selection should be one which minimizes reverberant sound from walls, ceilings and other equipment. Electricals should be installed so that they are protected from damage and exposure.

Exposed metal parts have been given a protective coating at the factory. This should be removed with a soft rag and kerosene or a good commercial solvent. Do not use an abrasive pad, as it may scratch polished metal surfaces.

7

Figure 1

Figure 2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Inch Planer More Information Warranty and ServiceTable of Contents Page Page 1791269 Introduction SpecificationsReceiving InstallationGrounding Instructions Installing Dust HoodDepth of Cut AdjustmentsFeed Rate Adjustment InspectionOpening Hood Knife Installation and Adjustment Straight Cutterhead onlyModel 201HH only Replacing or Rotating Knife Inserts Helical Cutterhead onlyAnti-Kickback Fingers Planer’s Feed SystemInfeed Roller Pressure Bar ChipbreakerTable Rollers Outfeed RollerTable Adjustments Operating Controls Test Cutting TroubleshootingSnipe Lubrication MaintenanceTroubleshooting Planer Operating Problems Troubleshooting Mechanical and Electrical Problems Replacement Parts Index No. Part No Description Size Qty Parts List Base Assembly6012067 Gearbox Assembly Parts List Gearbox Assembly Column Assembly Parts List Column Assembly Table Assembly Parts List Table Assembly Parts List Top Cover Assembly Cutterhead Assembly Parts List Cutterhead Assembly 6012180 Electrical Connections 1 Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt

201HH specifications

The Powermatic 201HH is a highly regarded 8-inch jointer, renowned for its robust construction, precision, and advanced technology. This machine is particularly well-suited for both professional woodworkers and serious hobbyists who demand the best performance from their tools.

One of the standout features of the Powermatic 201HH is the Helical Cutterhead. This technology distinguishes it from standard jointers featuring straight knives. The helical design incorporates numerous small, square inserts that can be rotated or replaced when worn, significantly extending the overall life of the cutterhead. The helical arrangement reduces noise during operation and provides a much smoother finish on the workpiece, minimizing the need for additional sanding.

Adjustability is another area where the Powermatic 201HH excels. It boasts an easy-to-use tables adjustment mechanism that allows users to fine-tune the infeed and outfeed tables for precise jointing. This feature is essential to ensure a perfectly flat and even surface on all types of wood. The large tables, measuring 74 inches in length, provide ample support for larger workpieces, making it easier to manage and maneuver materials during operation.

The 201HH also comes equipped with a powerful 3 HP motor that drives the machine with reliability and performance. This motor is a key component in delivering consistent power and maintaining speed even under heavier workloads. Coupled with a strong base and solid construction, the jointer maintains stability during operation, which contributes to both safety and precision.

Added convenience comes in the form of an integrated dust collection port, which facilitates cleaner operation by effectively managing sawdust and shavings. This reduces cleanup time and creates a more pleasant working environment.

Moreover, the design of the Powermatic 201HH incorporates safety features, including a push block that assists in guiding stock through the machine, minimizing the risk of injury. The solid build quality and attention to detail in the engineering provide confidence to users that they are working with a reliable tool that will stand the test of time.

In summary, the Powermatic 201HH offers an impressive array of features including a helical cutterhead, extensive adjustability, a powerful motor, efficient dust collection, and strong safety measures. These characteristics make it a top choice for anyone looking to achieve exceptional results in their woodworking projects.
Top Page Image Contents