Powermatic Troubleshooting Planer Feed Rollers Slipping Issues
Page 19

Troubleshooting: Planer Operating Problems

Trouble

Snipe.

Fuzzy grain.

Torn grain.

Rough/raised grain.

Rounded, glossy surface.

Poor feeding of lumber.

Probable Cause

Remedy

 

 

Table rollers not set properly.

Adjust table rollers to proper height.

 

 

Inadequate support of long boards.

Support long boards with a roller

stand.

 

 

 

Uneven feed roller pressure front to

Adjust feed roller tension.

back.

 

 

 

Dull knives.

Sharpen or replace knives.

Rotate or replace knife inserts.

 

 

 

Lumber not butted properly.

Butt end-to-end each piece of stock

as they pass through.

 

 

 

Planing wood with a high moisture

Remove moisture from wood by

content.

drying, or use different stock.

 

 

Dull knives.

Sharpen or replace knives.

Rotate or replace knife inserts.

 

 

 

Too heavy a cut.

Adjust proper depth of cut.

 

 

Knives cutting against grain.

Try to cut with the grain for finish cut.

 

 

Dull knives.

Sharpen or replace knives.

Rotate or replace knife inserts.

 

 

 

Dull knives.

Sharpen or replace knives.

Rotate or replace knife inserts.

 

 

 

Excessive depth of cut.

Decrease cutting depth.

 

 

Moisture content too high.

Remove moisture from wood by

drying, or use different stock.

 

 

 

Dull knives.

Sharpen or replace knives.

Rotate or replace knife inserts.

 

 

 

 

Adjust feed roller tension. If proper

Inadequate feed roller pressure.

tension cannot be achieved, replace

 

feed roller(s).

 

 

Planer table rough or dirty.

Clean off pitch and residue; apply

light coat of paste wax to planer table.

 

 

 

Belts are slipping.

Check belt tension and make any

needed adjustments.

 

 

 

Surface of feed rollers has been worn

Lightly roughen the feed roller surface

too smooth.

with sandpaper.

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Inch Planer More Information Warranty and ServiceTable of Contents Page Page 1791269 Introduction SpecificationsReceiving InstallationGrounding Instructions Installing Dust HoodDepth of Cut AdjustmentsFeed Rate Adjustment InspectionOpening Hood Knife Installation and Adjustment Straight Cutterhead onlyModel 201HH only Replacing or Rotating Knife Inserts Helical Cutterhead onlyAnti-Kickback Fingers Planer’s Feed SystemInfeed Roller Pressure Bar ChipbreakerTable Rollers Outfeed RollerTable Adjustments Operating Controls Test Cutting TroubleshootingSnipe Lubrication MaintenanceTroubleshooting Planer Operating Problems Troubleshooting Mechanical and Electrical Problems Replacement Parts Index No. Part No Description Size Qty Parts List Base Assembly6012067 Gearbox Assembly Parts List Gearbox Assembly Column Assembly Parts List Column Assembly Table Assembly Parts List Table Assembly Parts List Top Cover Assembly Cutterhead Assembly Parts List Cutterhead Assembly 6012180 Electrical Connections 1 Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt

201HH specifications

The Powermatic 201HH is a highly regarded 8-inch jointer, renowned for its robust construction, precision, and advanced technology. This machine is particularly well-suited for both professional woodworkers and serious hobbyists who demand the best performance from their tools.

One of the standout features of the Powermatic 201HH is the Helical Cutterhead. This technology distinguishes it from standard jointers featuring straight knives. The helical design incorporates numerous small, square inserts that can be rotated or replaced when worn, significantly extending the overall life of the cutterhead. The helical arrangement reduces noise during operation and provides a much smoother finish on the workpiece, minimizing the need for additional sanding.

Adjustability is another area where the Powermatic 201HH excels. It boasts an easy-to-use tables adjustment mechanism that allows users to fine-tune the infeed and outfeed tables for precise jointing. This feature is essential to ensure a perfectly flat and even surface on all types of wood. The large tables, measuring 74 inches in length, provide ample support for larger workpieces, making it easier to manage and maneuver materials during operation.

The 201HH also comes equipped with a powerful 3 HP motor that drives the machine with reliability and performance. This motor is a key component in delivering consistent power and maintaining speed even under heavier workloads. Coupled with a strong base and solid construction, the jointer maintains stability during operation, which contributes to both safety and precision.

Added convenience comes in the form of an integrated dust collection port, which facilitates cleaner operation by effectively managing sawdust and shavings. This reduces cleanup time and creates a more pleasant working environment.

Moreover, the design of the Powermatic 201HH incorporates safety features, including a push block that assists in guiding stock through the machine, minimizing the risk of injury. The solid build quality and attention to detail in the engineering provide confidence to users that they are working with a reliable tool that will stand the test of time.

In summary, the Powermatic 201HH offers an impressive array of features including a helical cutterhead, extensive adjustability, a powerful motor, efficient dust collection, and strong safety measures. These characteristics make it a top choice for anyone looking to achieve exceptional results in their woodworking projects.
Top Page Image Contents