Grizzly Model G0550 Chip Breaker, Tightening gib bolts in cutterhead G0550/G0551 15 Planer

Page 35

4.Place the knife setting jig over the knife on the cutterhead as shown in Figure 33. The knife setting jig will push the knife into posi- tion in the cutterhead.

Figure 33. Proper knife setting jig placement.

5.While holding the position of the knife setting jig, adjust the jack screws, located on each end of the knife, until they make contact with the bottom of the knife.

6.While holding the position of the knife setting jig, tighten the gib bolts down again in the cutterhead (Figure 34). Tighten the bolts evenly from the middle, working toward the ends.

7.Repeat these steps for the other two knives.

Chip Breaker

The chip breaker is located on the top side of the planer and extends down around the front of the cutterhead. Its function is to prevent tear-out or deep, unregulated gouging as the knives remove material. The chip breaker works by breaking the woodchips as they are being cut by the cutter- head. The chip breaker also deflects and expels the woodchips away from the surface of the board and out of the planer.

To check the chipbreaker:

1.Disconnect the machine from the power source!

2.Ensure that the knives are properly adjusted.

3.Place the gauge block on the table directly under the cutterhead.

4.Using a 1mm feeler gauge between the gauge block and the cutterhead, raise the table until one of the knives just touches the feeler gauge. Rotate the cutterhead by turn- ing the V-belts to be sure the knife is at bot- tom dead center.

5.Lock the table by tightening the table lock knobs.

6.Remove the feeler gauge and slide the gauge block under the chip breaker. See Figure 35. The chip breaker should just touch the top of the gauge block. Slide the gauge block to the opposite end of the chip breaker and check it in the same manner.

Figure 34. Tightening gib bolts in cutterhead.

 

 

 

 

 

 

 

 

 

 

 

 

G0550/G0551 15" Planer

-33-

Image 35
Contents Model G0550/G0551 PlanerPage Table Of Contents Safety Instructions For Power Tools SafetyLength Read this Entire Manual Before Turning the Planer on Additional Safety Instructions For PlanersCommentary IntroductionCircuit Breaker Circuit RequirementsAmperage Draw Plug-Type220V Operation Circuit Capacity Extension CordsGrounding Machine features G0550/G0551 15 Planer Machine FeaturesCommon Terms & Definitions Unpacking SET UPAbout This Section Parts Inventory G0550 Loose Parts Bolt Measure Hardware Recognition ChartWorking Clearances Site Considerations Clean UpFloor Load To assemble the open stand Beginning Assembly G0550 Open StandTools Needed Components and Hardware Needed Qty Mounting Planer G0550Dust Port Handwheel Dust port installedBed roller Extension RollersTo assemble the knife setting jig Knife Setting JigFactory adjustments that should be verified Start Up Recommended AdjustmentsGeneral Cutterhead Locks OperationsDepth Limiter Power Feed HandwheelType Anti-Kickback Wood SpeciesType Shear PSI Before each use, look for the following condi- tions MaintenanceMaintenance Safety Belts To inspect the gearbox GearboxLubricationGearbox fill point Planing Difficulties Gauge Blocks Service AdjustmentsAbout Service To adjust for gap differences Table AdjustmentThickness Scale To adjust the scaleKnife Inspection Knife Sharpening Knife SettingTightening gib bolts in cutterhead G0550/G0551 15 Planer Chip BreakerGauge block under chip breaker Feed Roller HeightBed Rollers To adjust roller heightTo adjust the bed rollers Roller pressure setscrews G0550/G0551 15 Planer Feed Roller PressureChip Deflector To adjust the chip deflectorGeneral Reference InfoPlaner Pals-See The Current Grizzly Catalog For Model #s Aftermarket AccessoriesMachine Data Sheet Grizzly Model G0551 15 Planer G0550/G0551 15 Planer G0550/G0551 15 Planer G0550/G0551 15 Planer Description Gear and Shaft Troubleshooting Guide Single Phase Power Source G0550/G0551 Wiring DiagramGauge Block Measurements Warranty & Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog