Delta 22-540 Leveling Extension Tables, Storing the Power Cord, Adjusting Knives

Page 10

LEVELING

EXTENSION TABLES

For optimum performance, the extension tables, one of which is shown at (A) Fig. 17, must be level with the planer table. To check the extension tables and adjust if necessary, proceed as follows:

1.Place a straight edge (B) Fig. 17, on the infeed ex- tension table (A) with one end extending out over the extension table as shown. Check to see if the infeed table is level with the planer table on both ends of the extension table.

2.If an adjustment is necessary, loosen locknut (C) Fig. 17, and adjust stop screw (D) on each side of the extension table (A) until the extension table is level with the planer table (E); then tighten locknut (C). Recheck and make certain inside edge of table extension is perfectly level with the planer table. If necessary, loosen two screws (F), adjust extension table and retighten two screws (F). Adjust opposite side of the table in the same manner. Make certain the extension table is solidly supported when there is downward pressure on the table.

3.Check and adjust outfeed extension table in the same manner.

STORING THE POWER CORD

Wire hangers (A) Fig. 18, are provided on the underside of the outfeed extension table as shown, to store the power cord (B) when the planer is not in use and when transporting the machine.

ADJUSTING KNIVES

To check and adjust the knives, proceed as follows:

1.DISCONNECT THE TOOL FROM THE POWER SOURCE.

2.Lower the head assembly by turning handle (B) Fig.

3.Remove chip deflector (A) Fig. 19.

4.Carefully place knife setting gage (B) Fig. 20, on the cutterhead so the rounded sections are directly over the knife as shown. When adjusted correctly, the knife should just contact the bottom of the center portion at each end of gage (B). Check the other knife in the same manner.

A

E

D B

C F

Fig. 17

A

B

Fig. 18

A

Fig. 19

B

Fig. 20

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Portable Planer Safety Rules Always Wear EYE ProtectionAdditional Safety Rules For Planers Connecting Tool to Power Source Power ConnectionsExtension Cords Minimum Gauge Extension CordUnpacking and Cleaning Assembling Raising and Lowering Handle Assembly InstructionsLowering Extension Tables Fastening Planer to Supporting Surface Assembling Chip DeflectorRaising and Lowering Head Assembly Operating Controls and AdjustmentsLocking Switch OFF Position Starting Stopping PlanerAdjusting Knives Storing the Power CordLeveling Extension Tables Replacing and Resetting Knives Operations Lifting StrapsBrush Inspection Replacement MaintenanceLubrication Accessories Page Page Maryland

22-540 specifications

The Delta 22-540 is a powerful and versatile woodworking tool designed for both amateur and professional woodworkers. Known for its robust construction and reliability, this 13-inch thickness planer features a host of technologies and characteristics that make it a standout choice in any workshop.

At the heart of the Delta 22-540 is its powerful 15-amp motor, which delivers impressive performance and allows users to tackle a range of materials with ease. The motor runs at a speed of 20,000 RPM, enabling smooth and efficient operation for various wood thicknesses. This ensures that users can achieve a uniform finish and consistent results every time.

One of the most notable features of the Delta 22-540 is its precision-ground, cast iron table. This heavy-duty tabletop provides a stable work surface that minimizes vibration during operation, which is essential for achieving a smooth finish. Additionally, the table has a dual adjustment system that allows for easy height adjustments, ensuring users can set the thickness precisely to their requirements.

The Delta 22-540 is equipped with high-quality knives that are easy to replace, ensuring longer tool life and enhanced cutting performance. The knife-edge design optimizes wood chip evacuation, which not only improves cutting efficiency but also reduces the likelihood of snipe, making it an ideal choice for users concerned about maintaining the quality of their wood surfaces.

Safety features are also a priority in the design of the Delta 22-540. The planer comes with a blade guard that protects users from accidental contact with the cutting blades. Furthermore, the onboard dust port promotes a cleaner workspace by connecting to a dust collection system, capturing debris and chips efficiently.

In terms of portability, the Delta 22-540 is designed with a sturdy yet lightweight frame, allowing for easy movement around the workshop. Its compact size makes it suitable for small spaces without sacrificing performance or capability.

Overall, the Delta 22-540 thickness planer combines power, precision, and user-friendly features, making it an excellent addition to any woodworking setup. Its blend of advanced technologies, durability, and safety characteristics ensures that woodworkers can complete their projects with confidence and ease, elevating their craftsmanship to the next level. Whether you are flattening rough lumber or bringing life back to old wood, the Delta 22-540 stands out as a reliable tool to achieve high-quality results.
Top Page Image Contents