Grizzly G0505 instruction manual Length AMP Rating, 25ft 50ft 100ft

Page 5

Safety Instructions For Power Tools

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace exten- sion cords if they become damaged.

Minimum Gauge for Extension Cords

 

 

LENGTH

 

 

 

 

 

 

AMP RATING

25ft

 

50ft

100ft

 

 

 

 

 

0-6

18

 

16

16

 

 

 

 

 

7-10

18

 

16

14

 

 

 

 

 

11-12

16

 

16

14

 

 

 

 

 

13-16

14

 

12

12

 

 

 

 

 

17-20

12

 

12

10

21-30

10

 

10

No

 

 

 

 

 

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool.

13.NEVER OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in. Also, the mag- netic switch on this machine may start if the switch gets bumped hard enough.

17.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.

20.NEVER USE UNDER THE INFLUENCE of alcohol or drugs, or when tired.

21. NEVER ALLOW UNSUPERVISED OR

UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to the oper- ation of the machine are approved, correct, safe, and clearly understood.

G0505 1212" Lean & Mean Portable Planer

-3-

Image 5
Contents 121⁄2 Lean & Mean Portable Planer Page Table Of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Portable Planer Introduction 110V Operation Circuit RequirementsGrounding Extension CordsIdentification Controls & FeaturesPiece Inventory SET UPUnpacking Hardware Recognition Chart Site Considerations Clean UpTo mount the planer Mounting to Bench Handle AssemblyTo attach the handle assembly To secure the chip deflector Chip Deflector Test RunOperations ON/OFF SwitchReset Button Planing Tips Depth Of CutWood Types Chip Marks or Indentations Wavy SurfacePitch & Glue Build-up Knife Sharpening MaintenanceGeneral To replace the belt MotorBeltLubrication To clean the feed rollersFeed Rollers Knife Setting Service AdjustmentsIf adjustment is necessary, proceed as fol- lows Extension WingsTo install and adjust the knives Reference Info Machine Data Sheet G0505 12 1⁄ 2 Lean & Mean Portable Planer Description G0505 121⁄2 Lean & Mean Portable Planer Motor Assembly G0505 12 1⁄ 2 Lean & Mean Portable Planer Base Assembly Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog