Grizzly G0477 Setting Up Moulding Guide Fence, Adjusting Moulding Guide Fence, Edge Moulding

Page 23

Setting Up Moulding

Guide Fence

Components and Hardware Needed:

Qty

Wing Bolts 1⁄4-20 x 11⁄4"

4

Flat Washers 1⁄4"

4

Cap Screw M5-.8 x 60

2

Flat Washer 5mm

2

Guide Fence Clamp

2

It is essential that you have a properly adjusted guide fence in place when moulding. Figure 22 on Page 22 features a plan for creating your own guide fence. We recommend using softwood or plywood for guide fence construction.

To fasten the guide fence to the planer/mould- er:

1.UNPLUG THE PLANER/MOULDER FROM THE POWER SOURCE!

2.Ensure that the threaded inserts indicated in Figure 22 on Page 22 are firmly in place.

3.Raise the planer/moulder headstock to its maximum height to provide working room.

4.Hand-fasten the guide boards to the base- board using the wing bolts and flat washers.

5.Fasten the baseboard to the table using the cap screws, flat washers and clamps, as shown in Figure 21.

Extension

Table

Clamp

Cap

Screw

Main

Table

Figure 21. Clamp installation.

Model G0477 15" Planer/Moulder

Adjusting Moulding

Guide Fence

To adjust the guide fences to fit a workpiece:

1.UNPLUG THE PLANER/MOULDER FROM THE POWER SOURCE!

2.Place the workpiece flush against the center guide.

3.Adjust the guide boards to fit the workpiece, allowing for smooth and even workpiece movement throughout the guide fence.

4.Fully tighten the wing bolts to fasten the guide boards in place.

Edge Moulding

Certain moulding tasks require the workpiece to be oriented vertically, and thus extra-tall guide boards are needed. Follow the plan shown in Figure 22 on Page 22, but increase the width of the center guide and the guide boards from 1⁄2" to to 1".

To prepare the guide fence for edge mould- ing:

1.UNPLUG THE PLANER/MOULDER FROM THE POWER SOURCE!

2.Replace the center guide and guide boards with extra-tall guides.

3.Follow Steps 2–4 of Adjusting Moulding Guide Fence on this page.

-21-

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model G0477 PLANER/MOULDER Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet Model G0477 15 Planer/Moulder Identification ON/OFF SwitchSafety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Planer/Moulders 110V Operation Circuit RequirementsUnpacking SET UPSet Up Safety Items Needed for Set UpComponents and Hardware not shown InventoryInventory Figure Qty Site Considerations Clean UpTo assemble the stand Stand AssemblyComponents and Hardware Needed Qty To mount the planer/moulder to the stand To install the dust chute and bagMounting Planer/ Moulder on Stand Dust Chute and BagTo test run the machine To install the crank handle FigureCrank Handle Test RunBasic steps of operating the planer/ moulder are as follows Operation Safety Safety Switch KeyOperations Basic OperationFeed Speed Operation TipsTo change the headstock height manually Headstock Height AdjustmentPreset Thickness Settings To use the preset depth gauge FigureTo adjust the infeed/outfeed roller height Roller Height AdjustmentTools Needed Qty Moulding KnivesEdge Moulding Setting Up Moulding Guide FenceAdjusting Moulding Guide Fence Wing Bolt G4520-G4564 Moulding Knives AccessoriesMaintenance Troubleshooting Guide ServicePlaner/Moulder Operations To change the planing knives Changing Planing KnivesTo correct a misaligned headstock Changing BeltsChain Tension and Headstock Leveling To change the drive and fan beltsTo replace motor brushes Changing Motor BrushesElectrical Components Wiring Diagram G0477 Body Breakdown G0477 Table and Base G0477 Gearbox Breakdown G0477 Stand Breakdown G0477 Labels Description Parts ListPSB26M CAP Screw M6-1 X Chain Protector Description Warranty and Returns Page Page Page
Related manuals
Manual 48 pages 176 b
Top Page Image Contents