Makita HM1202C instruction manual Assembly, Indicator lamp, Installing or removing the bit

Page 5

Number on adjusting dial

Blows per minute

6

1,900

5

1,800

4

1,600

3

1,300

2

1,050

1

950

002898

CAUTION:

•The speed adjusting dial can be turned only as far as 6 and back to 1. Do not force it past 6 or 1, or the speed adjusting function may no longer work.

The side handle can be swung 360° on the vertical and secured at any desired position. It also secures at eight different positions back and forth on the horizontal. Just loosen the clamp nut to swing the side handle to a desired position. Then tighten the clamp nut securely.

The side handle also can be mounted in the rear groove. Loosen the clamp nut and widen the side handle base. Slide the side handle back to the rear groove and secure it with the clamp nut.

1

1.

Side handle

 

 

base

 

2.

Clamp nut

Indicator lamp

For HM1202C only

1

2

002899

1.Power-ON indicator lamp (green)

2.Service indicator lamp (red)

2

002904

Installing or removing the bit

Clean the bit shank and apply bit grease before installing the bit.

1. Bit grease

2. Bit shank

The green power-ON indicator lamp lights up when the tool is switched ON. If the indicator lamp is lit but the tool does not start, the carbon brushes may be worn out, or the electric circuit or the motor may be defective. If the indicator lamp does not light up and the tool does not start, the ON/OFF switch or the mains cord may be defective.

The red service indicator lamp lights up when the carbon brushes are nearly worn out to indicate that the tool needs servicing. After approx. 8 hours of use, the motor will automatically be shut off.

1 2

002916

Insert the bit into the tool. Turn the bit and push it in until it engages.

ASSEMBLY

CAUTION:

•Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

Side handle (auxiliary handle)

1

2

002922

1.Bit

2.Tool holder cover

1

1.

Side handle

 

2.

Clamp nut

2

 

 

002903

 

 

If the bit cannot be pushed in, remove the bit. Pull the tool holder cover down a couple of times. Then insert the bit again. Turn the bit and push it in until it engages.

After installing, always make sure that the bit is securely held in place by trying to pull it out.

To remove the bit, pull the tool holder cover down all the way and pull the bit out.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Demolition Hammer Marteau Piqueur Martillo Demoledor General Safety Rules For All Tools SpecificationsEnglish Original instructions Cause you to lose controlMinimum gage for cord Ampere Rating Volts Specific Safety Rules120 25 ft 50 ft 100 ft 150 ft More Than Not More Than AWGSwitch action SymbolsFunctional Description Speed changeIndicator lamp AssemblyInstalling or removing the bit Side handle auxiliary handleOperation MaintenanceAccessories Warranty Policy Makita Limited ONE Year WarrantySpécifications Conservez CE Mode DemploiRègles de sécurité générales Pour Tous LES OutilsChoc électrique ou de blessures Une pièce tournante de loutil peut provoquer des blessuresUtilisation et entretien des outils Avertissement SymbolesRègles DE Sécurité Particulières Assemblage Description DU FonctionnementInterrupteur VoyantUtilisation Installation et retrait du emboutAngle du foret Burinage / Ecaillage / DémolitionLubrification Remplacement des charbonsEntretien Politique de garantie AccessoiresGarantie Limitée D’UN AN Makita Normas Generales DE Seguridad EspecificacionesPara todas las herramientas Guarde Estas InstruccionesUso y cuidado de la herramienta Más de No más de Calibre del cable AWG 10 a Normas Específicas DE Seguridad Advertencias y precauciones12 a 16 a No se recomiendaDescripción DEL Funcionamiento SímbolosCambio de velocidad Accionamiento del interruptorInstalación o extracción del cincel EnsambleEmpuñadura lateral auxiliar Mantenimiento OperaciónCincelado/Tallado/Demolición LubricaciónAccesorios incluidos o no Política de garantía 11-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan USA only

HM1202, HM1202C specifications

The Makita HM1202C and HM1202 are innovative demolition hammers designed for heavy-duty applications, combining high performance with advanced technology to deliver optimal results. These powerful tools are perfect for contractors, construction professionals, and DIY enthusiasts looking for reliable equipment to tackle tough tasks.

One of the standout features of the Makita HM1202C and HM1202 is their robust 10 AMP motor. This powerful motor ensures that both models deliver exceptional impact energy, making them highly effective for demolishing concrete, brick, and masonry. The HM1202C offers a maximum impact energy of 9.6 joules, while its companion model, the HM1202, provides a slightly lower impact energy, catering to various job requirements.

Both models are equipped with an impressive blow frequency, allowing users to achieve faster work rates. This is particularly beneficial during large-scale demolition or renovation projects where time is of the essence. Additionally, the hammers come with a soft-start feature, providing greater control upon initial activation, which enhances user safety and precision.

The design of the HM1202C and HM1202 includes an ergonomic structure that minimizes user fatigue during extended use. The tools feature a rubberized grip that absorbs vibrations, allowing for comfortable handling even in challenging working conditions. Furthermore, the integrated anti-vibration technology significantly reduces vibrations and enhances user comfort, making these hammers ideal for long periods of operation.

Another key characteristic of the Makita HM1202C and HM1202 is their durability. Constructed with high-quality materials, these demolition hammers are designed to withstand tough working environments and ensure longevity. The built-in dust collection system further protects the motor and internal components from debris, maintaining performance and reliability.

Additionally, both models are compatible with a range of chisels and bits, giving users versatility for various applications. This adaptability makes them suitable for both heavy-duty tasks and more delicate jobs, allowing professionals to achieve excellent results across different projects.

In summary, the Makita HM1202C and HM1202 demolition hammers are powerful, durable, and user-friendly tools that cater to the needs of construction professionals. With their advanced technology, ergonomic design, and compatibility with a variety of attachments, these hammers are reliable solutions for any demolition task, ensuring efficiency and effectiveness on every job site.
Top Page Image Contents