Miller Electric NT 456 CC, NT 456 CV Maintenance & Troubleshooting, Routine Maintenance, Fuse F1

Page 28

SECTION 6 − MAINTENANCE & TROUBLESHOOTING

6-1. Routine Maintenance

! Disconnect power before maintaining.

. Maintain more often during severe conditions.

n = Check	Z = Change	~ = Clean	Δ = Repair	l = Replace
* To be done by Factory Authorized Service Agent

Every 3 Months

nl Labels

n~ Weld Terminals

Every 3 Months

nΔ lCables And Cords

Every 6 Months

~:Durning heavy service, clean monthly.

6-2. Fuse F1

! Disconnect input power be- fore opening rear access door.

1Fuse F1 (See Parts List For Rating)

Fuse F1 protects control transform- er from overload. If F1 opens, weld output and fan motor stops. Re- place F1.

Close door when finished.

Tools Needed:

3/8 in

Ref. 800 101-C

OM-2243 Page 24

Image 28

Contents OM-2243212 113T ProcessesDescription File MultiprocessFrom Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-2243 Nameplate Safety Symbols − DefinitionsSpecifications − InstallationDuty Cycle And Overheating CC Mode CV ModeVolt-Ampere Curves 100 200 300 400 500 600Selecting a Location Movement LocationDimensions Dimensions And WeightsWeight Be careful when placing or moving unit over uneven surfaces Turn Off power before connecting to receptacleTipping VAC Receptacle And Circuit BreakersConnecting Weld Output Cables Weld Output Terminals And Selecting Cable SizesConnecting Remote Control Turn off power before conRemote 14 Receptacle Information SocketElectrical Service Guide Placing Jumper LinksConnecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Con- nections = GND/PE Earth Ground− Operation ControlsMeter Functions For CC/CV Models Lift-Arc TIG Procedure For CC/CV Models Touch Seconds Do not Strike Like a Match− Maintenance & Troubleshooting Routine MaintenanceDisconnect power before maintaining Disconnect input power be- fore opening rear access doorHE.L Voltmeter/Ammeter Help DisplaysTroubleshooting Trouble Remedy− Electrical Diagram Circuit Diagram For NT 456 CC/CV Models− Parts List Main AssemblyTHERMISTOR, NTC 10K OHM @ 25 DEG C 34IN Lead Panel, Front With Components 14 12 274Panel, Front With Components -1Item IGBT/Capacitor Assembly IGBT/Capacitor Assembly -1item 221Panel, Rear With Components Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s