Miller Electric S-64, S-62 manual Optional Equipment DIP Switch Settings, Voltage Sensing Function

Page 20

4-9. Optional Equipment DIP Switch Settings

. If wire feeder is equipped with a voltage sensing lead, set DIP switch S3

to the OFF position (up). If wire feeder is NOT equipped with a voltage sensing lead, set DIP switch S3 to the ON position (down).

Spot Time

Range SelectionOption Interface

Standard Settings

OFF

2	1

	OFF

2

1

1 2

X Means switch can be in either position.

. Means switch must be in this position.

Long Spot

Time

0-5 Seconds

Or

Short Spot

Time

0-2.5 Seconds

OFF

2 1

							Digital Meter Functions
	Standard									Standard						High Speed										High Speed
	Standard									Standard						High Speed										High Speed
			Motor								Motor							Motor									Motor
Inches/Minute									Meters/Minute							Inches/Minute									Meters/Minute

							5					5											5								5
							5					5											5								5


							4							4									4								4
							4							4									4								4
																								Or

							3	Or						3									3								3
							3	Or						3									3								3


							2					2											2								2
							2					2											2								2


							1							1									1								1
							1							1									1								1

	Voltage Sensing Function
	Arc Voltage Sensing Using	Arc Voltage Sensing Using
	Arc Voltage Sensing Using	Feedback From Welding
	Voltage Sensing Lead	Power Source
	2	2
	Or
	1	1
	DIP Switch S3	DIP Switch S3
Tools Needed:	Set To OFF	Set To ON
Tools Needed:

1/4 in

802 479 / Ref. SA-146 866-B / Ref. SA-148 666-E / Ref. SA-150 588-D

OM-1579 Page 16

Image 20

Contents Description OM-1579Processes From Miller to You Table of Contents Directives StandardsSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersSignification des symboles Consignes DE Securite Lire Avant UtilisationUN Choc É Lectrique peut tuer LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Bruit peut affecter l’ouïe LE Soudage peut provoquer un incendie ou une explosionDES Particules Volantes peuvent blesser les yeux Risque D’INCENDIE OU LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut DES Organes Mobiles peuvent provoquer des blessuresConsignes relatives aux stimulateurs cardiaques Principales normes de sé curitéInformation sur les champs é lectromagné tiques + + + DefinitionsSymbols And Definitions Rating Label For CE ProductsInstallation SpecificationsIntroduction Site SelectionEquipment Connection Diagrams Gun Recommendation TableRear Panel Connections And Rotating Drive Assembly Wire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityPin Plug Information Motor Start ControlInstalling And Threading Welding Wire To adjust drive roll pressure, hold nozzleVoltage Sensing Function Optional Equipment DIP Switch SettingsSpot Time Range SelectionOption Interface Standard Settings Operation Front Panel ControlsMaintenance and Troubleshooting Routine MaintenanceDisconnect power before maintaining Overload Protection And Optional Side Panel ControlsTroubleshooting Disconnect power before troubleshootingElectrical Diagram Circuit Diagram196 503-A Parts List Main AssemblyOptional Control Box Control Box -1 Item Control Panel Control Panel -2 Item Drive Assembly, Wire Drive Assembly, Wire -1 Item Roll Drive Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Service SupportOwner’s Record Miller Electric Mfg. Co