Miller Electric OM-222, 394F manual Feeder Set Up Push Button, Adjust Knob

Page 26

6-8. Feeder Set Up Push Button

3

4 Sequence

Trigger Control

Trigger Hold

2

Feeder Set Up

 

Start

Crater

 

Time

Time

1

Preflow

 

 

 

Postflow

 

Time

 

Time

 

 

 

 

 

 

 

 

 

 

 

 

 

Sequence Diagram

1Feeder Set Up Push Button LED

2Feeder Set Up Push Button

Press button to choose Sequence. Feeder Set Up push-button LED will illuminate.

3 Sequence LED

When the Feeder Set Up button is pressed once, the Sequence LED will illuminate and the upper display will show sequence options. Use the Adjust knob to select PRE (preflow), STRT (start), CRTR (crater), or POST (postflow).

Press the lower display push button and the Lower Display push-button LED will illuminate as well as the lower display. The Time LED will automatically begin flashing indicating that a time value can be entered by turning the Adjust knob. By entering a time value the sequence state will become active. To turn off a sequence state, change the time value to OFF. To step back for selecting another sequence option, press

the Upper Display push button.

The Sequence option STRT and CRTR will have additional parameter settings. By pushing the Lower Display push button a second time, while STRT or CRTR appear in the upper display, allows entering voltage (MIG) or Arc Adjust [Pulse, Accu-pulse, or RMD (optional)]. Use the Adjust knob to change the values indicated by the flashing LED for either Volts or Arc Adjust. Pressing the Lower Display push button a third time will activate the WFS setting for either STRT or CRTR and the WFS LED will begin flash- ing. Use the Adjust knob to change the WFS value.

Pressing the Feeder Set Up button two more times will exit the Sequence menu and return the system to standby mode.

4 Trigger Control LED

Press the Feeder Set Up button twice and the Trigger Control LED will illuminate, and the upper display will show the different trig-

ger control selections. Use the Adjust knob to cycle through the trigger control methods as follows: DS, TH, TDS, TPS, and 4T (see Section 5-1for definitions). The lower dis- play will show the current state of each trig- ger control method as being on or off. Not all trigger control methods are compatible with each other, therefore, turning on certain trig- ger selections will cause other trigger selec- tions to turn off.

Press the lower display push button to illu- minate the push-button LED and enable the use of the Adjust knob to allow turning se- lected trigger control methods on or off. If trigger hold is set to on, the Trigger Hold LED will illuminate.

.Trigger Hold is automatically set to On

with the 4T trigger selection. This is part of the 4T function.

Press the Feeder Set Up button a third time to cycle back to standby mode.

6-9. Adjust Knob

1 Adjust Knob

The Adjust knob is used to change functions and parameters. Refer to the front panel sections for information regarding use of this control.

1

Adjust

OM-222 394 Page 22

Image 26
Contents Description OM-222 394FProcesses File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Introduction − InstallationSpecifications Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Pin Network Receptacle Information Gun Recommendation TableInstalling And Threading Welding Wire Power Source Upper Display Lower Display Voltage Range Power Source Display At Power UpDual Schedule Switch Option − Operation Operational TermsPreflow Feeder Set UpGeneral Terms Sequence StartPower Switch Power SwitchLeft/Right Select Switch Jog/Purge Jog/Purge Push Button Gun Trigger Receptacle Adjust KnobJog/Purge switch provides the following functions Front Panel Sections Upper Display Volts Arc AdjustProgram Push Button Upper DisplayLower Display Sequence Trigger Control Trigger Hold Feeder Set Up Feeder Set Up Push ButtonAdjust Knob Process Set Up Push Button CO2Mild Steel Reset ModePulse Accu-pulseSequence Parameters − Setting Sequence ParametersSequence Parameters In a Program − Maintenance Routine MaintenanceDiagnostics Closed error Indicates a triggerTrouble Remedy TroubleshootingDisconnect power before troubleshooting − Electrical Diagram Circuit Diagram218 564-D − Parts List 21 − FigurePart Description Quantity Control Box PC1 Drive Assembly, Wire Drive Assembly, Wire -1Item1.4 mm Metric1.2 mm Page Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s