Miller Electric 394F, OM-222 Introduction, Installation, Specifications, Selecting a Location

Page 13

SECTION 3 − INTRODUCTION

3-1. Specifications

	Type of Input	Welding Power	Wire Feed Speed Range	Wire Diameter	Welding Circuit	Overall	Weight
	Power	Source Type	Wire Feed Speed Range	Range	Rating	Dimensions	Weight
	Power	Source Type		Range	Rating	Dimensions

	40 Volts DC	Axcess Series	Standard: 40 To 1400 ipm (1.0	.030 To 1/8 in	100 Volts,	Length: 27 in (686	87 lb
	10 Amperes		To 35.6 mpm)	(0.8 To 3.2 mm)	750 Amperes,	mm)	(39.5 kg)
					100% Duty	Width: 12-1/2 in
				Max Spool	Cycle	Width: 12-1/2 in
				Max Spool	Cycle	(318 mm)
				Weight: 60 lb (27		(318 mm)
				Weight: 60 lb (27		Height: 14-1/2 in
				kg)		Height: 14-1/2 in
						(368 mm)

SECTION 4 − INSTALLATION

4-1. Selecting A Location

Movement

OR

1

2

Tipping	Y Do not move or operate
	unit where it could tip.

Location

YSpecial installation may be required where gasoline or volatile liquids are present − see NEC Article 511 or CEC Section 20.

4

3

18 in

(460 mm)

18 in

(460 mm)

YDo not stack units. Beware of tipping.

1 Lifting Forks

Use lifting forks to move unit.

Extend forks beyond opposite side of unit.

2 Hand Cart

Use cart or similar device to move unit.

3 Rating Label

Use rating label to determine input power needs.

4 Line Disconnect Device

Locate unit near correct input power supply.

loc_2 3/96 - 804 018-A

OM-222 394 Page 9

Image 13

Contents Processes OM-222 394FDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéSpecifications − Installation− Introduction Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Gun Recommendation Table Pin Network Receptacle InformationInstalling And Threading Welding Wire Dual Schedule Switch Option Power Source Display At Power UpPower Source Upper Display Lower Display Voltage Range Operational Terms − OperationGeneral Terms Sequence Feeder Set UpPreflow StartLeft/Right Select Switch Power SwitchPower Switch Jog/Purge switch provides the following functions Jog/Purge Push Button Gun Trigger Receptacle Adjust KnobJog/Purge Front Panel Sections Program Push Button Volts Arc AdjustUpper Display Upper DisplayLower Display Adjust Knob Feeder Set Up Push ButtonSequence Trigger Control Trigger Hold Feeder Set Up CO2 Process Set Up Push ButtonPulse Reset ModeMild Steel Accu-pulseSequence Parameters In a Program − Setting Sequence ParametersSequence Parameters Routine Maintenance − MaintenanceDiagnostics Indicates a trigger Closed errorDisconnect power before troubleshooting TroubleshootingTrouble Remedy Circuit Diagram − Electrical Diagram218 564-D 21 − Figure − Parts ListPart Description Quantity Control Box PC1 Drive Assembly, Wire -1Item Drive Assembly, Wire1.2 mm Metric1.4 mm Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s