Protective Cover, Wire Feeders/Guns | Miller Electric XMT 350 VS

Genuine Miller Accessories (continued)

Protective Cover

Coolmate™ V3 #043 009 115 VAC

#195 478 Mildew and water resistant, odor-free cover protects your machine’s finish. For 300/350 A inverters: XMT, Maxstar and Dynasty.

Wire Feeders/Guns

SuitCase® X-TREME™8VS #300 093 SuitCase® X-TREME™12VS #195 500

Lightweight, portable wire feeder for a variety of wires up to .062 in. Holds up to an 8 in (8VS) or 12in (12VS) spool of wire. Operates on open-circuit voltage eliminating the need for a control/power cord. See Lit. Index No. M/6.4 and M/6.41.

Spoolmatic® 30A #130 831

A 1-lb, air-cooled spool gun that extends the weld process range by adding a handy portable system for small wire MIG. Rated 200 A at 100% duty cycle. Includes 30 ft (9.1 m) cable assembly. (WC-24 #137 549 for 14 pin.)

Ironmate™ Flux Cored Guns

See Lit. Index No. AY/16.0.

FC-1260

#195 732 10 ft (3 m) #195 729 15 ft (4.6 m)

FC-1260LM

#194 912 10 ft (3 m) #194 911 15 ft (4.6 m)

FC-1150

#194 864 10 ft (3 m) #194 863 15 ft (4.6 m)

For use with water-cooled torches rated up to 500 amps. Vertical design conveniently mounts to Miller cylinder rack in place of one cylinder.

Coolmate™ 4 #042 288 115 VAC

For use with water-cooled torches rated up to 600 amps. Tough molded polyethylene case with carrying handle.

Coolant #043 810

Sold in cases of four 1-gallon recyclable plastic bottles. Miller coolants contain a base of ethylene glycol and deionized water to protect against freezing to -37˚F (-38˚C) or boiling to 227˚F (108˚C). Also contains a compound that resists algae growth.

International-Style Connectors

Note: XMT 350 power sources are equipped with International-style connectors for secondary connections. (Power source is shipped with two 50-mm male International-style plugs for use with #1 or #2 AWG size cable.)

International/Tweco®

Adapter #042 465

International/Cam-Lok

Adapter #042 466

SuitCase® 8RC/12RC #194 938/#194 940 Lightweight, portable wire feeder for a variety of wires up to .062 in. Holds up to an 8 in (8RC) or 12 in (12RC) spool of wire. Operates using 14-pin control receptacle. See Lit. Index No. M/6.5.

XR Control #181 538 Push-pull wire feed system offers unparalleled performance for aluminum MIG

welding. See Lit. Index No. M/1.7.

70 Series
S-74S	#195 057
S-74D	#195 058
S-74DX	#195 059
S-74MPa	#300 411

Wire feeder features Posifeed™ wire drive assembly and handles a variety of wires up to 1/8 in. Comes with FREE Bernard® Q™-Gun. See Lit. Index No. M/3.0.

Water Coolant Systems

For more information, see the Miller Coolant Systems literature sheet, Index No. AY/7.2.

Coolmate™ 3

#043 007 115 VAC #043 008 230 VAC

For use with water-cooled torches rated up to 600 amps. Unique paddle-wheel indicator, external filter and easy-fill spout.

One-piece adapter with International-style male plug (to power source) on one end and female receptacle (Tweco or Cam-Lok for weld cable connection) on other end.

International-Style Connector Kit #042 418 50 mm

Accepts #4 or #1/0 AWG cable size. Required if male plugs shipped with power source must be replaced, or if additional plugs are needed.

#042 533 70 mm

Accepts #1/0 or #2/0 AWG cable size. Required if #1/0 or #2/0 AWG size cable is to be used.

Kit includes one International-style male plug which attaches to the work and/or weld cables and plugs into the International-style receptacles on the power source.

Extension Kit for International-Style Cable Connectors

#042 419 50 mm

Accepts #4 or #1/0 AWG size cable.

#042 534 70 mm

Accepts #1/0 or #2/0 AWG size cable.

Used to adapt or extend weld and/or work cables. Kit includes one male International- style plug and one in-line female International-style receptacle.

Genuine Miller Accessories (continued)