Miller Electric UPC 838 manual Definitions

Page 13

SECTION 3 − DEFINITIONS

3-1. Warning Label Definitions

8

9

11

10

Warning! Watch Out! There are possible hazards as shown by the symbols.

1Cutting sparks can cause explosion or fire.

1.1Keep flammables away from cutting. Do not cut near flammables.

1.2Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.

1.3Do not cut on drums or any closed containers.

2The plasma arc can cause injury and burns.

2.1Turn off power before disassembling torch.

2.2Do not grip material near cutting path.

2.3Wear complete body protection.

3Electric shock from torch or wiring can kill.

3.1Wear dry insulating gloves. Do not wear wet or damaged gloves.

3.2Protect yourself from electric shock by insulating yourself from work and ground.

3.3Disconnect input plug or power before working on machine.

4Breathing cutting fumes can be hazardous to your health.

4.1Keep your head out of the fumes.

4.2Use forced ventilation or local exhaust to remove the fumes.

4.3Use ventilating fan to remove fumes.

5Arc rays can burn eyes and injure skin.

5.1Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection.

6Become trained and read the instructions before working on the machine or cutting.

7Do not remove or paint over (cover) the label.

8Falling equipment can cause injury and damage to unit.

9Always lift and support unit using both handles. Keep angle of lifting device less than 60 degrees.

10Use a proper cart to move unit.

11Do not use one handle to lift or support unit.

11/00

OM-202 515 Page 9

Image 13

Contents Processes OM-202 515CDescription Page Table of Contents Standards DirectivesMarks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosionFlying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearingCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulierLE Bruit peut endommager l’ouïe Risque de blessure en casLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresDES Pieces Chaudes peuvent pro- voquer des brûlures graves LES Bouteilles peuvent exploser si elles sont endommagéesDES Organes Mobiles peuvent provoquer des blessures DES Particules Volantes peuvent blesser les yeuxInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques − Definitions 60 s Air Supply Precaution Use Only Oil Free Dry Compressed AirManufacturer’s Rating Label For CE Products Symbols And DefinitionsI1max I1effSpecifications − InstallationDuty Cycle And Overheating UPC Cutting SpeedSelecting a Location Dimensions And WeightMovement Do not move or operate unit Electrical Service Guide Connecting Work Clamp And Gas/Air SupplyInput Voltage Input Amperes At Rated Cutting Capacity= GND/PE Connecting Input PowerControls − Operation4070 Setting Gas/Air Pressure Example Of Cutting Operation Sequence Of OperationTrigger is pressed Routine Maintenance − Maintenance & TroubleshootingEach Use Every WeekChecking Shield Cup Shutdown System Trouble LightsTrouble Remedy TroubleshootingOM-202 515 Circuit Diagram For Power Source − Electrical Diagram202 Complete Assembly − Parts ListDia Unitor Mkgs Description Quantity Torch, ICE-80C ICE−80C Consumables Unitor Page Page Owner’s Record