Miller Electric ST 44 Series Drive Roll And Wire Guide Kits 4 Drive Roll, 1.2 mm, Cogged

Table 7-1. Drive Roll And Wire Guide Kits (4 Drive Roll)

NOTE

Base selection of drive rolls upon the following recommended usages:

1.V-Grooved rolls for hard wire.

2.U-Grooved rolls for soft and soft shelled cored wires.

3.U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).

4.V-Knurled rolls for hard shelled cored wires.

5.Drive roll types may be mixed to suit particular requirements (example: V-Knurled roll in combination with U-Grooved).

	Wire Diameter		Kit No.		Drive Roll		Wire Guide
Metric	Fraction	Decimal		Part No.		Type	Inlet	Intermediate
0.6 mm	0.023/0.025 in	0.023/0.025 in	087 132	087 130		V-Grooved	056 192	056 206
0.8 mm	0.030 in	0.030 in	046 780	053 695		V-Grooved	056 192	056 206
0.9 mm	0.035 in	0.035 in	046 781	053 700		V-Grooved	056 192	056 206
1.0/1.2 mm	0.035/0.045 in	0.035/0.045 in	N/A	189 285		V-Grooved	156 193	056 207
1.0 mm	0.040 in	0.040 in	191 917	053 696		V-Grooved	056 192	056 206
1.2 mm	0.045 in	0.045 in	046 782	053 697		V-Grooved	056 193	056 207
1.6 mm	1/16 in	0.062 in	046 784	053 699		V-Grooved	056 195	056 209
0.9 mm	0.035 in	0.035 in	044 750	072 000		U-Grooved	056 192	056 206
1.2 mm	0.045 in	0.045 in	046 785	053 701		U-Grooved	056 193	056 207
1.3 mm	0.052 in	0.052 in	046 786	053 702		U-Grooved	056 193	056 207
1.6 mm	1/16 in	0.062 in	046 787	053 706		U-Grooved	056 195	056 209
2.0 mm	5/64 in	0.079 in	046 788	053 704		U-Grooved	056 195	056 209
0.9 mm	0.035 in	0.035 in	046 782	132 958		V-Knurled	056 192	056 206
1.2 mm	0.045 in	0.045 in	046 793	132 957		V-Knurled	056 193	056 207
1.3 mm	0.052 in	0.052 in	046 794	132 956		V-Knurled	056 193	056 207
1.6 mm	1/16 in	0.062 in	046 795	132 955		V-Knurled	056 195	056 209
1.8 mm	0.068-0.072 in	0.068-0.072 in	089 985	132 959		V-Knurled	056 195	056 209
2.0 mm	5/64 in	0.079 in	046 796	132 960		V-Knurled	056 195	056 209
1.2 mm	0.045 in	0.045 in	083 319	083 489		U-Cogged	056 193	056 207
1.3 mm	0.052 in	0.052 in	083 320	083 490		U-Cogged	056 193	056 207
1.6 mm	1/16 in	0.062 in	046 800	053 708		U-Cogged	056 195	056 209
2.0 mm	5/64 in	0.079 in	046 801	053 710		U-Cogged	056 195	056 209

OM-216 655 Page 20