Miller Electric XLT 185 warranty Replacing Switch And/Or Head Tube

Page 29

7-7. Replacing Switch And/Or Head Tube

Y Turn Off welding power source /wire feeder and disconnect gun.

1 Remove handle locking nut.

3 Slide handle.

2 Remove switch housing. Install new switch and connect leads (polarity is not important). Reassemble in reverse order. If replacing head tube, continue to end of figure.

4Secure head tube in vice.

5Loosen jam nut. Remove from vice and turn head tube out by hand.

6 Hand-tighten head tube into cable connector.

7Place head tube in vice and tighten until nuts are tight.

8Remove from vice. Reposition handle and install switch housing. Secure with handle locking nut.

Tools Needed:

19 mm

Ref. ST-800 795-C

OM-230 832 Page 25

Image 29

Contents OM-230 832A 2007−02 Processes Arc Welding Power Source and Wire FeederDescription Flux Cored Arc FcawPage Table of Contents Typical MIG Process Connections − Parts List− MIG Welding Gmaw Guidelines Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut endommager l’ouïeLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphoneSymbols And Definitions − SpecificationsSpecifications − DefinitionsVolt-Ampere Curves Duty Cycle And OverheatingAmperes OutputInstalling Welding Gun − InstallationClose door IncorrectInstalling Work Clamp Changing Polarity Process/Polarity TableTools Needed 1-1/8 Installing Gas SupplyAfter flow is set, close feedhead pressure assembly First, and never to a line ter- minal Selecting a Location And Connecting Input PowerTools Needed Electrical Service GuideInstalling Wire Spool And Adjusting Hub Tension Installing Contact Tip And Nozzle Threading Welding Wire Controls Wire Speed Control− Operation CFH Weld Parameter Chart For 230 VAC Model227010 Routine Maintenance − Maintenance &TROUBLESHOOTINGDisconnect power before maintaining Overload Protection Drive Motor ProtectionTurn Off power before replacing contact tip Changing Drive Roll Or Wire Inlet GuideReplacing Gun Contact Tip 030/.035 Groove Stamped 023/.025 Groove Stamped .030/.035Install gas diffuser, adapter, contact tip, and nozzle Cleaning Or Replacing Gun LinerDisconnect gun from unit To Reassemble GunReplacing Switch And/Or Head Tube Trouble Remedy Troubleshooting TableOM-230 832 Circuit Diagram − Electrical Diagram228 180-A − MIG Welding Gmaw Guidelines Regulator Flowmeter Wire Feeder Power Source ShieldingTypical MIG Process Connections GasWire Size Amperage Range Typical MIG Process Control SettingsThickness to Amperage a Select VoltageHolding And Positioning Welding Gun Push Conditions That Affect Weld Bead ShapePerpendicular Drag Short Normal LongGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Troubleshooting − Porosity Troubleshooting − Excessive SpatterTroubleshooting − Excessive Penetration Possible Causes Corrective ActionsTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Distortion Troubleshooting − Waviness Of BeadCommon MIG Shielding Gases Weld beadTroubleshooting Guide For Semiautomatic Welding Equipment OM-230 832 Main Assembly − Parts ListDia Part 228 195 H-10 GunOptions Optional Drive RollsPage Work like a Pro Warranty Owner’s Record