Miller Electric XLT 185 warranty Parts List, Main Assembly

Page 44

SECTION 10 − PARTS LIST

		22
		53
		21
	15	20
14		20
14	16	18
		19
		17
13		26
12

27

	11
	10
52	9
8
7
6
5			29
4			29
3				35
				35
	34
			36
2	49	32 31	30
	33
	48
1				43
	47			44
	50		46
	51		45	54

Figure 10-1. Main Assembly

.Hardware is common and not available unless listed.

	23
25	24

28

37

39

38

40

42

41

804 624-A

OM-230 832 Page 40

Image 44

Contents Arc Welding Power Source and Wire Feeder OM-230 832A 2007−02 ProcessesDescription Flux Cored Arc FcawPage Table of Contents Typical MIG Process Connections − Parts List− MIG Welding Gmaw Guidelines Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresBoulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone En ce qui concerne les stimulateurs cardiaques− Specifications Symbols And DefinitionsSpecifications − DefinitionsDuty Cycle And Overheating Volt-Ampere CurvesAmperes Output− Installation Installing Welding GunClose door IncorrectInstalling Work Clamp Process/Polarity Table Changing PolarityTools Needed 1-1/8 Installing Gas SupplyAfter flow is set, close feedhead pressure assembly Selecting a Location And Connecting Input Power First, and never to a line ter- minalTools Needed Electrical Service GuideInstalling Wire Spool And Adjusting Hub Tension Installing Contact Tip And Nozzle Threading Welding Wire Controls Wire Speed Control− Operation Weld Parameter Chart For 230 VAC Model CFH227010 − Maintenance &TROUBLESHOOTING Routine MaintenanceDisconnect power before maintaining Overload Protection Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide Turn Off power before replacing contact tipReplacing Gun Contact Tip 030/.035 Groove Stamped 023/.025 Groove Stamped .030/.035Cleaning Or Replacing Gun Liner Install gas diffuser, adapter, contact tip, and nozzleDisconnect gun from unit To Reassemble GunReplacing Switch And/Or Head Tube Troubleshooting Table Trouble RemedyOM-230 832 − Electrical Diagram Circuit Diagram228 180-A Regulator Flowmeter Wire Feeder Power Source Shielding − MIG Welding Gmaw GuidelinesTypical MIG Process Connections GasTypical MIG Process Control Settings Wire Size Amperage RangeThickness to Amperage a Select VoltageHolding And Positioning Welding Gun Conditions That Affect Weld Bead Shape PushPerpendicular Drag Short Normal LongGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Troubleshooting − Excessive Spatter Troubleshooting − PorosityTroubleshooting − Excessive Penetration Possible Causes Corrective ActionsTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Waviness Of Bead Troubleshooting − DistortionCommon MIG Shielding Gases Weld beadTroubleshooting Guide For Semiautomatic Welding Equipment OM-230 832 − Parts List Main AssemblyDia Part 228 H-10 Gun 195Optional Drive Rolls OptionsPage Work like a Pro Warranty Owner’s Record