Miller Electric XLT 185 warranty Optional Drive Rolls, Options

Page 48

10-3. Optional Drive Rolls

	For All Feed Head Assemblies

PART NO.		WIRE DIAMETER
PART NO.		INCHES (mm)
		INCHES (mm)

202 925		.023/.025 (.6) and .030/.035 (.8 and .9)

202 926		.030/.035 (.8 and .9) and .045 (1.2 VK Groove)

10-4. Options

PART NO.	DESCRIPTION	REMARKS

770 187	Running Gear/Cylinder Rack	For One Small Gas Cylinder, 100 lb (45 kg) max.

194 776	Small Running Gear/Cylinder Rack	For One Small Gas Cylinder, 75 lb (34 kg) max.

195 957	H-10 Replacement Gun	10 ft length/.030-.035 wire size

212 492	Regulator/Flowmeter	For use with CO2 shielding gas, 10−50 CFH
144 108	Gas Hose 5 ft	For use with regulator/flowmeter 212 492

NOTE: If individual parts are required, see Parts List chapter of this manual for part number to order.

OM-230 832 Page 44

Image 48

Contents Arc Welding Power Source and Wire Feeder OM-230 832A 2007−02 ProcessesDescription Flux Cored Arc FcawPage Table of Contents − Parts List − MIG Welding Gmaw GuidelinesTypical MIG Process Connections Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier LE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresBoulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone En ce qui concerne les stimulateurs cardiaques− Specifications Symbols And DefinitionsSpecifications − DefinitionsDuty Cycle And Overheating Volt-Ampere CurvesAmperes Output− Installation Installing Welding GunClose door IncorrectInstalling Work Clamp Process/Polarity Table Changing PolarityInstalling Gas Supply After flow is set, close feedhead pressure assemblyTools Needed 1-1/8 Selecting a Location And Connecting Input Power First, and never to a line ter- minalElectrical Service Guide Installing Wire Spool And Adjusting Hub TensionTools Needed Installing Contact Tip And Nozzle Threading Welding Wire Wire Speed Control − OperationControls Weld Parameter Chart For 230 VAC Model CFH227010 − Maintenance &TROUBLESHOOTING Routine MaintenanceDisconnect power before maintaining Overload Protection Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide Turn Off power before replacing contact tipReplacing Gun Contact Tip 030/.035 Groove Stamped 023/.025 Groove Stamped .030/.035Cleaning Or Replacing Gun Liner Install gas diffuser, adapter, contact tip, and nozzleDisconnect gun from unit To Reassemble GunReplacing Switch And/Or Head Tube Troubleshooting Table Trouble RemedyOM-230 832 − Electrical Diagram Circuit Diagram228 180-A Regulator Flowmeter Wire Feeder Power Source Shielding − MIG Welding Gmaw GuidelinesTypical MIG Process Connections GasTypical MIG Process Control Settings Wire Size Amperage RangeThickness to Amperage a Select VoltageHolding And Positioning Welding Gun Conditions That Affect Weld Bead Shape PushPerpendicular Drag Short Normal LongPoor Weld Bead Characteristics Good Weld Bead CharacteristicsGun Movement During Welding Troubleshooting − Excessive Spatter Troubleshooting − PorosityTroubleshooting − Excessive Penetration Possible Causes Corrective ActionsTroubleshooting − Lack Of Penetration Troubleshooting − Incomplete FusionTroubleshooting − Burn-Through Troubleshooting − Waviness Of Bead Troubleshooting − DistortionCommon MIG Shielding Gases Weld beadTroubleshooting Guide For Semiautomatic Welding Equipment OM-230 832 − Parts List Main AssemblyDia Part 228 H-10 Gun 195Optional Drive Rolls OptionsPage Work like a Pro Warranty Owner’s Record