Miller Electric 714D manual Program Push Button, Upper Display, Non-CE Models

Page 22

5-4. Program Push Button

1

2

Non-CE Models

Program

3

1

2

1 Program Display

CE Models

The number of the active program is displayed.

2 Program Push Button

Press button to activate program select feature. To change the pro- gram number, press the Program push button and rotate the Adjust control.

3 Program Push Button LED

3 The LED lights to indicate the Pro- gram push button is active.

5-5. Upper Display

.Factory voltage settings are V-Min 10 and V-Max 38. If you

are using a power source with a different voltage range, see Section 5-10 for V-Min And V-Max adjustments.

Non-CE Models

1

 

4

 

Volts

Time (sec)

 

5

CE Models

1

4

5

3

2

3

2

1 Upper Display

The upper display shows voltage or time. The unit displays both preset and actual arc voltage. When the unit is in a welding state, actual arc voltage is displayed. The upper display shows welding sequence time when the Time LED is illuminated.

2 Upper Display Push Button

Press button to choose between voltage or time functions.

3 Upper Display Push Button LED

The upper display push button LED illumi- nates to indicate that information displayed can be changed by the Adjust control.

4Volts LED

5Time LED

The LEDs below the display illuminate to in- dicate which value is being shown.

At any time while welding, the unit permits the adjustment of the weld sequence voltage and overrides the display of actual arc volt- age.

•If the current detect override is in the On position (see Section 4-7), the unit dis- plays preset voltage while welding instead of actual arc voltage. Preset voltage is de- fined as the desired arc voltage com- manded to the welding power source.

•If the unit is displaying a welding sequence that can be timed, the welding time display mode is entered by pressing the upper dis- play push button repeatedly until welding

time is the active parameter in the upper display. At idle, the upper display toggles between showing weld voltage or weld time, with subsequent presses of the up- per display push button.

•The unit defaults to displaying welding voltage when a welding sequence display mode is first entered. When the unit is in a welding state, the welding time display mode is terminated in place of the voltage display mode.

•If the weld sequence has a time set (as in spot time), after the weld program is com- pleted, ERR TRIG will be displayed to indi- cate the weld program is complete. Re- lease trigger to clear error.

OM-1500-1 Page 18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Processes OM-1500-1Description From Miller to You Table of Contents Directives StandardsArc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersUN Choc É Lectrique peut tuer Signification des symbolesConsignes DE Securite Lire Avant Utilisation LES Fumé ES ET LES GAZ peuvent ê tre dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionLE Bruit peut affecter l’ouïe ’EMPLOI Excessif peut Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresInformation sur les champs é lectromagné tiques Principales normes de sé curitéConsignes relatives aux stimulateurs cardiaques + + + DefinitionsSymbols And Definitions Rating Label For CE ProductsIntroduction InstallationSpecifications Site SelectionRear Panel Connections And Rotating Drive Assembly Gun Recommendation Table Wire Type, Size, And Feed Speed Capability TablePin Plug Information PinInstalling And Threading Welding Wire Extending from outlet wire guide asSetting Internal DIP Switches Operation Power SwitchOperational Terms Front Panel Controls Wire SpeedTime sec Non-CE Models Program Push ButtonUpper Display CE ModelsSetup Push Button Lower DisplayAdjust Control Sequence Push ButtonOM-1500-1 Auxiliary Menus Non-CE ModelsAuxiliary Menu Trigger Hold SetupReset To Factory Settings Run-InJog/Purge Setting Sequence Parameters Sequence Parameters In a ProgramOptional Dual Schedule Switch Diagrams Setting Dual Schedule ParametersMaintenance Routine MaintenanceDiagnostics LED3-Related Error IndicationsElectrical Diagram Circuit DiagramOM-1500-1 Parts List Main AssemblyPart Description Quantity Control Box Detach Option 2ftDrive Assembly, Wire Drive Assembly, Wire -1 Item 23 contin UedRoll Drive Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll Drive KitPage Page Service SupportOwner’s Record Miller Electric Mfg. Co
Top Page Image Contents