Miller Electric 714D manual Directives, Standards

Page 4

Declaration of Conformity for

European Community (CE) Products

Note This information is provided for units with CE certification (see rating label on unit).

Manufacturer’s Name:

Manufacturer’s Address:

Declares that the product:

Miller Electric Mfg. Co.

1635 W. Spencer Street

Appleton, WI 54914 USA

714D

conforms to the following Directives and Standards:

Directives

Low Voltage Directive: 73/23/EEC

Electromagnetic Compatibility (EMC) Directive: 89/336/EEC

Machinery Directives: 89/392/EEC, 91/368/EEC, 93/C 133/04, 93/68/EEC

Standards

Arc Welding Equipment Part I: Welding Power Sources: IEC 60974-1

(September 1998 – Second Edition)

Arc Welding Equipment: Wirefeed Systems: IEC 974-5

(September 1997 – Draft Revision)

Degrees of Protection Provided By Enclosures (IP Code): IEC 529

(November 1989 – First Edition)

Insulation Coordination For Equipment With Low-Voltage Systems:

Part I: Principles, Requirements and Tests: IEC 664-1

(October 1992 – First Edition)

Electromagnetic Compatibility, (EMC): EN 50199

(August 1995)

European Contact: Mr. Danilo Fedolfi, Managing Director

MILLER Europe S.r.l.

Via Privata Iseo

20098 San Giuliano

Milanese, Italy

Telephone: 39(02)98290-1

Fax: 39(02)98281-552

dec_con 11/96

Image 4
Contents Processes OM-1500-1Description From Miller to You Table of Contents Directives StandardsSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersSignification des symboles Consignes DE Securite Lire Avant UtilisationUN Choc É Lectrique peut tuer LES Fumé ES ET LES GAZ peuvent ê tre dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionLE Bruit peut affecter l’ouïe Risque D’INCENDIE OU LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut DES Organes Mobiles peuvent provoquer des blessuresInformation sur les champs é lectromagné tiques Principales normes de sé curitéConsignes relatives aux stimulateurs cardiaques + + + DefinitionsSymbols And Definitions Rating Label For CE ProductsInstallation SpecificationsIntroduction Site SelectionRear Panel Connections And Rotating Drive Assembly Wire Type, Size, And Feed Speed Capability Table Pin Plug InformationGun Recommendation Table PinInstalling And Threading Welding Wire Extending from outlet wire guide asSetting Internal DIP Switches Operation Power SwitchOperational Terms Front Panel Controls Wire SpeedTime sec Program Push Button Upper DisplayNon-CE Models CE ModelsSetup Push Button Lower DisplayAdjust Control Sequence Push ButtonOM-1500-1 Auxiliary Menus Non-CE ModelsTrigger Hold Setup Reset To Factory SettingsAuxiliary Menu Run-InJog/Purge Setting Sequence Parameters Sequence Parameters In a ProgramSetting Dual Schedule Parameters MaintenanceOptional Dual Schedule Switch Diagrams Routine MaintenanceDiagnostics LED3-Related Error IndicationsElectrical Diagram Circuit DiagramOM-1500-1 Parts List Main AssemblyPart Description Quantity Control Box Detach Option 2ftDrive Assembly, Wire Drive Assembly, Wire -1 Item 23 contin UedDrive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive Roll Drive KitPage Page Service SupportOwner’s Record Miller Electric Mfg. Co