Hitachi DH24PB2 instruction manual Maintenance and Inspection

Page 17

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection.

1.Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted.

2.Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this rotary hammer with loosen screws is extremely dangerous.

3.Maintenance of the motor

The motor unit winding is the very ÒheartÓ of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4.Inspecting the carbon brushes

For your continued safety and electrical shock protection, carbon brush inspection and replacement on this tool should ONLY be performed by a HITACHI AUTHORIZED SERVICE CENTER.

5.How to replace grease

Low viscosity grease is applied to this rotary hammer so that it can be used for a long period without replacing the grease. Please contact the nearest service center for grease replacement when any grease is leaking from loosened screw. Further use of the rotary hammer despite the grease shortage causes seizure to reduce the service life.

CAUTION: A specific grease is used with this machine, therefore, the normal performance of the machine may be badly affected by use of other grease. Please be sure to let one of our service agents undertake replacement of the grease.

6.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

17

Image 17

Contents Rotary Hammer Marteau rotatif Martillo perforador Manual DE Instrucciones E Instrucciones DE SeguridadContents Meanings of Signal Words Safety English Never touch moving parts Blades and accessories must be securely mounted to the toolNever operate without all guards in place Use right toolOperate power tools at the rated voltage Keep motor air vent cleanNever use a tool which is defective or operating abnormally Do not wipe plastic parts with solventMake Them Available to Other Users Owners of this Tool Name of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Mounting the drill bit Fig Switch operation HOW to USESelecting the driver bit Confirm the direction of bit rotation FigRotation only Rotation + HammeringWhen driving wood screws Fig When driving machine screws FigMounting HOW to USE the Core BIT for Light LoadUsing depth gauge Fig Dismounting. Fig How to bore FigMaintenance and Inspection Sold separately AccessoriesStandard Accessories Drill Bit Taper shank and taper shank adaptor   Outer wedge type with the female screw Knock-in anchor Rotation + HammeringInner wedge type with the headless screw Outer wedge type with Female screwCrushing operation Rotation + Hammering Large hole boring Rotation + HammeringGuide plate Drilling holes rotation only Dust cup, Dust collector B Driving Screws rotation onlyPhillips Driver Bit Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéRegles Generale DE Securite SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Utiliser l’outil correct Regles DE Securite Specifiques ET SymbolesNE Jamais toucher les parties mobiles Garder propres les évents d’air du moteur Manipuler l’outil correctementUtiliser l’outil motorisé à la tension nominale Ne pas essuyer les parties en plastique avec du solvant22. Définitions pour les symboles utilisés sur cet outil Double Isolation Pour UN Fonctionnement Plus SUR 4600/min Poids Lbs 2,4 kg Description FonctionnelleNOM DES Parties Avertissement Avant L’UTILISATIONMontage du foret de perçage Fig Sélection de la mèche pour visseuse UtilisationVérifiez la direction de rotation de La mèche Fig Fonctionnement de l’interrupteurRotation seulement Rotation + percussionEnfoncement de vis à bois Fig Lors du vissage des vis machine FigConique Utilisation de la quenouille FigComment utiliser la mèche queue Perçage Fig Comment Utiliser LA Couronne Pour UNE Charge LegereMontage Démontage Fig Entretien ET Inspection Vendus séparément AccessoiresAccessoires Standard Cône en a Foret de perçage queue conique et raccord de queue coniqueType à cale intérieure avec vis sans tête Ancrage de chasse Rotation + percussionType à cale extérieure avec vis femelle Travail de démolissage Rotation + percussion Perçage de trou à large diamètre Rotation + percussionPlaque centrale de guidage Perçage de trous rotation seulement Capuchon anti poussière, Collecteur à poussière B Vis d’entraînement rotation uniquementEmbout de vissage Phillips Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadNo limpie las partes de plástico con disolvente Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas Hertzios VoltiosAmperios Velocidad sin cargaAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones 4600/min Peso Lbs 2,4 kgAplicaciones Montaje Y Opera CiónAntes DE LA Operación AdvertenciaPrecaucion Montaje de la broca FigSelección de la broca destornillador Como SE USAConfirmar la dirección de rotación De la broca Fig Operación del conmutadorRotación solamente Rotación + golpeteoAtornillando tornillos para madera Fig Cuando coloque tornillos para Metal FigModo de usar el tope Fig Modo de taladrar Fig Modo DE Usar LA Barrena Tubular Para Cargas LigerasMontaje Desmontaje Fig Mantenimiento E Inspección Broca de taladro vástago cónico y adaptador cónico AccesoriosAccesorios Estándar Ancla de martillar Rotación + golpeteo Tipo de reborde interior con tornillo sin cabeza Tipo de reborde exterior con tornillo hembraTrabajo de roturación Rotación + golpeteo Placa guiaBroca para tornillos Plillips Perforación rotación solamenteCopa de polvo, Colector de polvo B Page 626VVMC2PS2L Kestrel Road Mississauga on L5T 1Z5